- 您現在的位置：買賣IC網 > PDF目錄367495 > L9824D Analog IC PDF資料下載
參數資料
| 型號： | L9824D |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 4/11頁 |
| 文件大?。?/td> | 229K |
| 代理商： | L9824D |
ELECTRICAL CHARACTERISTICS
(continued)
Symbol
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
t
n
ON
ON-delay Time (5)
See fig. 1
R
L
= 1K
10
ms
μ
s
μ
s
μ
s
μ
s
μ
s
μ
s
μ
s
t
n
OFF (3)
t
s
ON
OFF-delay Time (5)
10
ON-delay Time (6)
20
100
t
s
OFF (3)
OFF-delay Time (6)
20
40
t
D
ON
t
D
OFF (3)
Data ON - Delay Time (7)
2
10
Data OFF - Delay Time (7)
2
10
t
ON
-t
OFF
t
f
Delay Time Difference
Except STANDBY MODE
4
Filter Time (8)
0.7
2
4
Notes :
2. If the output current exceeds thehigh short current threshold I
SC
an internal timeris started. If afterthetime period of T
TSC
the current
limitingis still active the overload condition is recognized andthis output is switchedoff. To restart the output theTRANSFER MODE
has to be chosen and the corresponding input voltage V
DIN
must become HIGH to reset the internal overload latch.
3. Becausethe output capacitance is the drain-source capacitance of the power switch the risetime ofthe outputs depends of the used
supply voltageV
S
, the load resistor R
L
and the output capacitance C
OUT
andcan be calculated with the followingequation :
T
d
=
τ
In10 (reaching 90% of V
S
)
τ
=R
L
xC
OUT
xK (4) K = 1.5
This additional delay time T
must be addedto t
.
4. Becausethe drain source capacitance of the output transistor is voltage dependent, it is necessary to multiply C
OUT
(specified at the
maximum V
OUT
) with a correction factor K to obtain the average output capacitance C
OUT
.
5. Delay timebetween all modes except STANDBYMODE.
6. Delay timebetween STANDBY MODE and any other mode and vice versa.
7. Data delay time when TRANSFER MODE is chosen.
8. Explanation see page 6.
MODE CHANGE DIAGRAM
.
Critical mode variations occur when both mode
inputschange their statesimultaneously.This is
representedby the diagonalarrows in the mode
changediagram.
FILTERING TIMING
.
To avoidthata filter is implementedin the TM si-
gnal path.A suitable filter time t
f
is chosen to be
well beyondthe mode comparatordelays.
L9824
4/11
相關PDF資料 |
PDF描述 |
|---|---|
| L9842N | Octal Peripheral Driver |
| L9842ND | Octal Peripheral Driver |
| L9864D | AUTOMOTIVE|DIAGNOSTIC SERIAL LINK|SOP|20PIN|PLASTIC |
| L9936 | DC Motor Controller/Driver |
| L9946 | DC Motor Controller/Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9825 | 功能描述:電源開關 IC - 配電 Octal Low Side RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| L9825_03 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Octal Low-side Driver For Resistive and Inductive Loads With Serial / Parallel Input Control, Output Protection and Diagnostic |
| L9825TR | 功能描述:功率驅動器IC Octal Low Side RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9826 | 功能描述:功率驅動器IC Octal Low Side RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9826_05 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Octal Low-Side Driver for Resistive and Inductive Loads with Serial/Parallel Input Control, Output Protection and Diagnostic |
發布緊急采購，3分鐘左右您將得到回復。