- 您現在的位置：買賣IC網 > PDF目錄30713 > L9942XP1TR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 2.5 A, PDSO24 PDF資料下載
參數資料
| 型號： | L9942XP1TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO24 |
| 封裝： | ROHS COMPLIANT, SSOP-24 |
| 文件頁數： | 20/40頁 |
| 文件大小： | 639K |
| 代理商： | L9942XP1TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
L9942
SPI - control and status registers
Doc ID 11778 Rev 6
5.8
Auxiliary logic blocks
5.8.1
Fault condition
Logical level at pin D0 represents fault condition. It is valid from first high to low edge of
signal CLK up to transfer of data bit D12. Fault bit is an logical OR of:
Control and status register 6 bit 5 and 6 for open load, bit 7 reference current failure
(RERR) and
Control and status register 7 bit 0 to bit 7 for overcurrent, bit 8 and 9 failure at VS
(UV,OV) and
bit 10 and bit 11 during high temperature (TW,TSD)
5.8.2
SPI communication monitoring
At the rising edge of the CSN signal the contents of the shift register will be transferred to
the selected data register. A counter monitors proper SPI communication. It counts rising
edges at pin CLK. The writing to the register is only enabled if exactly 16 bits are transmitted
within one communication frame (i.e. CSN low). If more or less clock pulses are counted
within one frame the complete frame will be ignored. This safety function is implemented to
avoid an activation of the output stages by a wrong communication frame. SPI
communication can be checked by loading a command twice and then answer at pin DO
must be same.
Note:
Due to this safety functionality a daisy chaining of SPI is not possible. Instead, a parallel
operation of the SPI bus by controlling the CSN signal of the connected ICs is
recommended.
5.8.3
PWM monitoring for stall detection
Control registers 4, 5, and 3 contain bits D0-D7, use for setting a stall detection threshold.
The value in this set of bits determine the minimum time for current rise over one quadrant of
motor driving. D7-D0 is compared with the sum of the rise times over one quadrant. When
the sum is less than the value stored in D7-D0 the ST bit (register 6 bit 8) is set to a logic “1”.
The PWM pin reflects the PWM control signal of the load current in bridge A. This is so after
power on when the SST bit (register 6, bit11) is reset to a logic “0”. If this bit is set to a
logical “1” then status of the ST bit 8 is mirrored to pin PWM. This provides stall detection
without the need of reading register 6 through the SPI bus.
相關PDF資料 |
PDF描述 |
|---|---|
| L9949TR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO20 |
| L9950XPTR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9950 | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9950TR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| L9953XPTR | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9946 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver |
| L9947 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD HALF-BRIDGE AND SINGLE HIGH-SIDE DRIVER |
| L9947L | 制造商:STMicroelectronics 功能描述: |
| L9947S | 功能描述:馬達/運動/點火控制器和驅動器 Quad Half Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9949 | 功能描述:功率驅動器IC Door Actuator RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。