- 您現在的位置：買賣IC網 > PDF目錄30728 > LB11692JH BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 PDF資料下載
參數資料
| 型號： | LB11692JH |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| 封裝： | 0.375 INCH, HSOP-36 |
| 文件頁數： | 10/12頁 |
| 文件大小： | 118K |
| 代理商： | LB11692JH |
LA4814V
No.A0972-7/17
9.Turn-off transient response characteristics
If the IC is turned off and then turned back on while there is a potential difference between the pin 7 (reference voltage,
plus input pin) and pins 5 and 10 (minus input pins), a louder pop noise than the one normally generated when power is
switched on will be emitted. Therefore, in order to minimize the turn-on pop noise, smoothen the discharge of the input
and output capacitors, and bring the potential of pin 7 and pins 5 and 10 to approximately the same level, then turn on
the IC.
a) Single ended mode
When the continuous changeover of mode between standby and operation is necessary, it is recommended to insert a
resistor between the output pins (pins 3 and 12) and ground to accelerate the turn-off transient response characteristic.
The value shown below is recommended for the resistor used for discharge. In order to reduce pop noise, it is
recommended that time necessary for turning the IC back on is greater than the following value.
Recommended discharge resistor : R = 4.7k
Ω
(Recommended turn-on time : T = 600ms)
b) BTL mode
When the continuous changeover of mode between standby and operation is performed, it is recommended that the
second amplifier control function be used to reduce the turn-on pop noise. If this function is used, the pop noise level
can be reduced regardless of the time taken for the IC to turn on after it is turned off.
For details on the time taken for the second amplifier to turn on after the IC is turned on, refer to Section 5 “Second
amplifier control function.”
PWR
→STBY
STBY
→PWR
100ms/div
OUT:50mV/div,AC
7pin:1V/div,DC
T
OUT1
IN1
Vref
3
5
+
-
+
C3
470
μ
F
R
L
4
Ω
R3
33k
Ω
R1 10k
Ω
10k
Ω
C1 0.22
μF
4.7k
Ω
相關PDF資料 |
PDF描述 |
|---|---|
| LB11696V | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB11696V | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB11824M | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO30 |
| LB11851TT | BRUSH DC MOTOR CONTROLLER, 0.02 A, PDSO10 |
| LB11921T | BRUSHLESS DC MOTOR CONTROLLER, 0.01 A, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11693 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for 24 V Fan Motors |
| LB11693H | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC 3-Phase Brushless Motor Driver for 24V Fan Motors |
| LB11693H-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11693H-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11693H-TRM-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。