- 您現在的位置：買賣IC網 > PDF目錄43902 > LB11820M BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO30 PDF資料下載
參數資料
| 型號： | LB11820M |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO30 |
| 封裝： | 0.375 INCH, MFP-30 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 484K |
| 代理商： | LB11820M |
No. 7104-7/17
LB11820M
Pin No.
9
10
11
12
13
14
15
16
17
18
19
20
Pin
IN1+
IN1–
IN2+
IN2–
IN3+
IN3–
VREG
VCC2
LVS
VCC3
12REG
TOC
Equivalent circuit
Function
Hall amplifier input.
IN+ > IN– is the input high state, and the reverse is
the input low state.
Connect a capacitor between the sIN+ and IN–
inputs if there is noise in the Hall sensor signals.
Regulated-voltage output pin (5V output)
Connect a capacitor (about 0.1 F) between this pin
and ground for stabilization.
Voltage detection pin for low-voltage protection.
To detect the supply voltage of 5 V or more, connect
the zenor diode in series to set the detection voltage.
Power pin (VCC3) for use during application with the
supply voltage of 12 V or more. 12 V is generated at
the 12 REG pin. To use the 12REG pin, connect this
pin to VCC1.
When not used, keep both VCC3 and 12 REG open
or connect them to GND.
PWM waveform comparator pin.
Normally used in the open condition.
By inputting the voltage directly into this pin, the
output duty can be controlled without using the
VCTL amp.
Power pin (PWM oscillation, PWM comparator,
VCTL amp). Normally connect to VREG.
Continued on next page.
Continued from preceding page.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11822 | BRUSHLESS DC MOTOR CONTROLLER, 3.1 A, DFM28 |
| LB11823M | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO36 |
| LB11847 | STEPPER MOTOR CONTROLLER, 1.75 A, PDIP28 |
| LB11868V | DISK DRIVE MOTOR CONTROLLER, PDSO20 |
| LB11870 | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11822 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LB11822-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11823M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Direct PWM Drive Brushless Motor Predriver for OA Products |
| LB11823M(36SOP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LB11824 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Direct PWM Drive Brushless Motor Predriver for On-Demand Water Heater and Air Conditioner Motors |
發布緊急采購，3分鐘左右您將得到回復。