- 您現在的位置：買賣IC網 > PDF目錄43902 > LB11876 (SANYO SEMICONDUCTOR CO LTD) BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36 PDF資料下載
參數資料
| 型號： | LB11876 |
| 廠商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36 |
| 封裝： | 0.275 INCH, SSOP-36 |
| 文件頁數： | 7/15頁 |
| 文件大?。?/td> | 168K |
| 代理商： | LB11876 |
LB11876
PS No.8317-15/15
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
12. Power saving circuit
This IC goes into a power saving state in which current drain is reduced when set to the stop state. This power saving
state is implemented by cutting the bias current to most of the circuits in the IC. The 5V regulator output, however, is
still output when the IC is in the power saving state.
13. Error amplifier system components
The external components for the error amplifier block must be located as close as possible to the IC to minimize the
influence of noise. These components must also be located as far from the motor as possible.
14. Forward/reverse switching
In principle, forward/reverse switching must be performed with the motor in the stopped state.
This IC does provide circuit workarounds for handling the through currents that occur during switching if the direction
is switched while the motor is turning. However, care is required with respect to lifting of the motor supply voltage
during this switching, since the motor current will return to the power supply during brief instants. If this becomes a
problem, the size of the capacitor connected between the power supply line and ground must be increased.
If the motor current after switching exceeds the current limit value, the PWM drive side output will be turned off.
However, the opposite side output will go to the short-circuit braking state and a current determined by the motor
induced voltage and the coil resistance. This current must be held under the current rating of the output transistors used.
(This aspect requires more care the faster the motor speed at which forward/reverse switching occurs.)
15. Brake switching
Either free running or short-circuit braking can be selected with the BRSEL pin.
The short-circuit braking mode adopts a form in which all phases of the PWM drive side output transistors are turned
on (all phases of the reverse side transistors are turned off). Care is required, since the current limiter function does not
operate during braking. During braking, the output circuits go to a shorted state with 100% duty. The current that flows
in the output transistors during braking is determined by the motor induced voltage and the coil resistance. This current
must be held under the current rating of the output transistors used. (This aspect requires more care the faster the motor
speed at which braking occurs.)
16. NC pins
Since the NC pins are electrically open, they can be used for intermediate wiring connections without problem.
This catalog provides information as of April, 2007. Specifications and information herein are subject
to change without notice.
相關PDF資料 |
PDF描述 |
|---|---|
| LB11889M | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO36 |
| LB11946 | STEPPER MOTOR CONTROLLER, 1.2 A, PDIP28 |
| LB11946 | STEPPER MOTOR CONTROLLER, 1.2 A, PDIP28 |
| LB11980H | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28 |
| LB11980H | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11876-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11876-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 PRINTER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB-1188 | 制造商:Ideal Industries Inc 功能描述:GRIPPER-SET C/STMLT .109/GRTPD |
| LB11880 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Sensorless Motor Driver with Loading Motor Driver |
| LB11885N | 制造商:SANYO Semiconductor Co Ltd 功能描述:Vcr Deck 3 In 1 Motor Driver Sanyo IC 48-Pin op-Hs SMD |
發布緊急采購，3分鐘左右您將得到回復。