- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1823 (Sanyo Electric Co.,Ltd.) Power Brushless Motor Predriver IC for OA Applications PDF資料下載
參數資料
| 型號： | LB1823 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Power Brushless Motor Predriver IC for OA Applications |
| 中文描述： | 功率無刷電機預驅動器集成電路的辦公自動化應用 |
| 文件頁數： | 10/11頁 |
| 文件大?。?/td> | 118K |
| 代理商： | LB1823 |
Output transistors
The output transistors must be chosen according to the current and breakdown voltage settings determined by the
required motor power. Printed circuit board space considerations determine the choice of discrete or driver array
components.
The 2SC4070 (SPA) and 2SC4113 (SPA) lower side predriver transistors include an emitter-base resistor.
When no resistor is required, the same transistors as used in the output interface can be used.
Driver arrays:
SLA6022 and SLA6023 (Sanken)
12. Through currents due to the direct PWM technique
In the direct PWM technique through currents flow in the outputs due to the switching, e.g., when used in a discrete
structure (including predriver circuits) or in LB1822 applications. These through currents are due to the delays and
parasitic capacitances in the output transistors. Although additional capacitors were previously used to deal with this
problem, the LB1823 includes circuit modifications to ameliorate through currents. However, even despite these
measures, through currents can still occur if the values of R17, R18 and R19 are made too large, since the switching
time of the lower side transistors will be increased. Although whiskers of under 10 ns can be seen in the R
f
voltage
waveform during switching, this will not be a problem. (These occur in the probe and do not correspond to current
flows.)
13. Oscillator element
Normally, a crystal resonator, a resistors, and two capacitors are connected to the LB1823 Xtal pin. A ceramic
oscillator could also be used in applications that do not require such precise speed control characteristics. To avoid
problems, consult with the manufacturer of the oscillator element when selecting the oscillator element and the
values of the external resistor and capacitors used. Use a circuit consisting of resistors and a pnp transistor as shown
in the figure to apply an external clock signal (CLK) to the Xtal pin.
f
CLK
= 1 to 10.2 MHz
Input signal levels
High level voltage: 4.0 V minimum
Low level voltage: 1.5 V maximum
Capacitors must be added to this circuit if overshoot
and/or undershoot appears in the input waveform. Be
sure to check for this condition in that case.
Reference values
No. 4263-10/11
LB1823
Upper side transistors
(Darlington)
Lower side transistors
Current
Breakdown voltage
2SA1259
2SD1060
5 A
50 V
2SB881
2SD1061
7 A
50 V
2SB882
2SD1062
10 A
50 V
2SB883
2SD1065
15 A
50 V
V
CC
= 6.3 V typ (5.8 to 6.8 V)
V
CC
= 5.0 V typ (4.5 to 5.5 V)
Ra = 1.5 k
Ra = 2.0 k
Rb = 2.0 k
Rb = 1.0 k
相關PDF資料 |
PDF描述 |
|---|---|
| LB1824 | Power Brushless Motor Driver for OA Equipment |
| LB1825 | Three-Phase Brushless Motor Driver |
| LB1830 | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1830M | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1831M | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1823-F-E | 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LB1823M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Power Brushless Motor Predriver IC for OA Applications |
| LB1824 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Power Brushless Motor Driver for OA Equipment |
| LB1825 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver |
| LB1830 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
發布緊急采購，3分鐘左右您將得到回復。