- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1823M (Sanyo Electric Co.,Ltd.) Power Brushless Motor Predriver IC for OA Applications PDF資料下載
參數資料
| 型號： | LB1823M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Power Brushless Motor Predriver IC for OA Applications |
| 中文描述： | 功率無刷電機預驅動器集成電路的辦公自動化應用 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 119K |
| 代理商： | LB1823M |
4. Speed lock range
The speed lock range is ±6.25% of the rated speed, and the LD pin (which is an open collector output) will be low
when the motor speed is within the lock range. The LB1823M controls the motor speed to be within the lock range
by generating a speed error signal when the motor speed goes out of the lock range and adjusting the motor drive on
duty according to that signal.
5. PWM frequency
The PWM frequency is determined by R1 and C3, which are connected to the CR pin.
When R1 is connected to a 6.3 V power supply (the application circuit pin 17 voltage):
f
PWM
≈
1/(0.6 · C · R)
R1 must not be any smaller than 30 k
. A PWM frequency of 15 kHz is desirable. If the PWM frequency is too low,
the motor will resonate at the PWM frequency during motor constraint. This can result in disturbing audible
frequency noise. Inversely, the output transistor switching loss can become significant if the PWM frequency is too
high.
6. Grounding
The signal system ground must be separated from the output system ground, and these grounds must be connected to
a single ground point at the connector. The output system ground should be kept as short as possible since it carries
large current.
Output system ground – – The R
f
(R10) ground side. The D1, D2, and D3 ground side.
Signal system ground – – The IC pin 24 and the IC peripheral circuit ground.
7. External interface pins
LD pin
Output type: open collector
Breakdown voltage:8 V
Manufacturing variation in the saturation voltage (reference value at I
LD
= 10 mA)
0.10 to 0.30 V
FGS pin
Output type: open collector
Breakdown voltage: 8 V
Manufacturing variation in the saturation voltage (reference value at I
FGS
= 2 mA)
0.05 to 0.10 V
The FGS pin outputs the FG amplifier output converted to a pulse signal by a hysteresis comparator. Thus FGS is a
speed monitor output. No pull-up resistor is required when unused.
S/S pin
Input type: PNP transistor base with a 63 k
pull-up resistor to V
CC
Threshold level: About 2.6 V (high to low), about 3.05 V (low to high)
(typical) Hysteresis: about 0.45 V
In the stop state, power is cut from all but certain circuits (the input, crystal oscillator and divider circuits) and the
LB1823M does not operate.
F/R pin
Input type: PNP transistor base with a 50 k
pull-down resistor to ground
Threshold level: About 2.6 V (high to low), about 3.05 V (low to high)
(typical) Hysteresis: about 0.45 V
The forward/reverse direction must be switched in the stop state.
BR pin
Input type: PNP transistor base with a 50 k
pull-down resistor to ground
Threshold level: About 2.6 V (high to low), about 3.05 V (low to high)
(typical) Hysteresis: about 0.45 V
Braking must be released in the stop mode.
No. 4696-8/11
LB1823M
相關PDF資料 |
PDF描述 |
|---|---|
| LB1823 | Power Brushless Motor Predriver IC for OA Applications |
| LB1824 | Power Brushless Motor Driver for OA Equipment |
| LB1825 | Three-Phase Brushless Motor Driver |
| LB1830 | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1830M | Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1824 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Power Brushless Motor Driver for OA Equipment |
| LB1825 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver |
| LB1830 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Low-Saturation Bidirectional Motor Driver for Low-Voltage Applications |
| LB1830M | 制造商:Panasonic Industrial Company 功能描述:IC |
| LB1830M_11 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Low-Voltage, Low-Saturation Bidirectional Motor Driver |
發布緊急采購，3分鐘左右您將得到回復。