- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1860M (Sanyo Electric Co.,Ltd.) Variable Speed Fan Motor Driver PDF資料下載
參數資料
| 型號： | LB1860M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Variable Speed Fan Motor Driver |
| 中文描述： | 變速風扇電機驅動器 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 79K |
| 代理商： | LB1860M |
.
From this relation, it can be observed that the ‘t
o
’ and ‘t
on
’ are in proportional relation with each other, and that the ‘t
on
/t
o
’
equals the ‘on’ time duty. As a result, a certain rotation speed can be fixed despite the fact that rotation speed exclusively
depends on each motor.
.
At the start, the ‘t
on
’ value becomes longer while the ‘t
off
’ value remains unchanged. This means that the ‘t
off
/t
o
’ duty becomes
small enough compared to normal rotation mode. Therefore, the same start torque as that of the full speed rotation can be
obtained because the ‘on’ operation time duty increases. This enables the motor to start at a very low speed.
The LB1860 has the internal parallel regulator which supplies power to the Hall amplifier circuit and the control block.
Therefore, the driver ICs are not affected by power source fluctuations and kickbacks from the motor. They maintain the stable
operations even if noise signals such as surge are generated.
.
Set the resistance R1 between V
CC
and V
IN
so that the I
CC
current of 6 mA to 50 mA can flow onto the V
IN
pin within the
supply voltage range of a fan motor.
.
V
IN
is 6.7 V typ at I
CC
= 7 mA.
.
The current flowing into V
IN
is calculated using the equation shown below.
(2) Supply voltage (V
IN
pin)
I
CC
=
V
CC
– V
IN
R1
............................
2
.
Consideration given to surge voltage
.
The maximum allowable current at V
IN
pin is 200 mA. Therefore, the pin is designed to withstand abnormal positive voltage of:
Vsurge
=
V
IN
+ R1
×
200 mA ............................................
3
(3) Hall input pin voltage (Pins IN
–
, IN
+
)
.
Set the voltage levels of the input pin for the Hall element output and the Hall element output voltage to within the range of
0 V to V
IN
– 1.5 V.
.
The gain between the hall input pin and the output pin is 100 dB or greater. The offset voltage of the hall input amp is
±
7 mV,
therefore, the hall element output must be set with the offset voltage (
±
7 mV) considered.
Output current
I
O
= 1.5 A max
.
Output saturation voltage
V
O
sat = 1.15 V/1.0 A typ
.
Output limiting voltage
V
OLM
= 57 V typ (LB1860, 1860M)
V
OLM
= 32 V typ (LB1861,1861M)
.
Since the LB1860 series have a protect zener diode between collector and base, the kickback voltage induced by the coil is cut
at V
OLM
= 57 V (32 V). When external capacitors are connected between OUT and GND, the capacitance should not exceed
10 μF.
Capacitor pin used in forming an automatic return circuit.
.
If rotation is stopped due to overload, the pin voltage level increases and then forces the output to become inactive. In this case,
after proper load adjustment, the output returns to the ‘drive’ mode from the ‘stop’ mode automatically. By changing the
capacitor value, the lock detect time period can be set.
(4) Output transistor (Pins OUT1, OUT2)
(5) Output protection function (C pin)
For C marked with 1 μF
Lock detect time
Lock protect time (output ON)
Approximately 2 sec.
Approximately 1 sec.
Approximately 6 sec.
(output OFF)
Rotation
Output ON
Output OFF
Output
ON
Output OFF
Rotation
Lock
Lock release
Automatic Return Circuit C Pin Voltage
LB1860,1860M,1861,1861M
No.3519-4/6
相關PDF資料 |
PDF描述 |
|---|---|
| LB1862M | Single-Phase Full-Wave Driver for Fan Motors |
| LB1862 | Fan Motor Single-Phase Full-Wave Driver |
| LB1863M | Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package |
| LB1868M | RES 10.0MEGOHM MTL FLM.40W 1% TR |
| LB1868 | Two-Phase Brushless Fan Motor Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1860M-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 FAN MOTOR RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1860M-TLM-H | 功能描述:馬達/運動/點火控制器和驅動器 FAN MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1861 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Variable Speed Fan Motor Driver |
| LB1861-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1861M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Variable Speed Fan Motor Driver |
發布緊急采購，3分鐘左右您將得到回復。