- 您現在的位置：買賣IC網 > PDF目錄358748 > LB1872 (Sanyo Electric Co.,Ltd.) Polygon Mirror Scanner Driver IC(多邊形鏡像掃描儀驅動器) PDF資料下載
參數資料
| 型號： | LB1872 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Polygon Mirror Scanner Driver IC(多邊形鏡像掃描儀驅動器) |
| 中文描述： | 多邊形鏡掃描儀驅動IC（多邊形鏡像掃描儀驅動器） |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 166K |
| 代理商： | LB1872 |
No. 5625-9/11
LB1872
Continued from preceding page.
Pin No.
Symbol
Pin function
Equivalent circuit
26
FG
IN
–
FG amplifier input
27
AGC
AGC amplifier frequency characteristics correction
Insert a capacitor (about 0.1 μF) between this pin and ground.
28
GND
Ground
LB1872 Functional Description
1. Speed control circuit
Since this IC adopts a PLL speed control circuit, it can provide high-precision, jitter-free, and stable motor operation.
This PLL circuit compares the phases of the CLK (external clock) rising edge and the FG Schmitt output rising edge
and uses the error output from that comparison for control.
If an internal clock system is used, the FG servo frequency is determined by the following formula. Therefore, the
motor speed can be set by setting the number of FG pulses and the crystal oscillator frequency.
f
FG
(servo) = f
OSC
/N
f
OSC
: Crystal oscillator frequency
N: Clock divisor (See the separately provided table.)
If an external clock (input to the N1 pin) is used, the IC controls the motor speed by holding the FG servo frequency
identical to the external clock frequency.
2. Output drive circuit
To suppress motor noise as much as possible, this IC adopts a three-phase full wave current linear drive technique.
Also, it adopts a midpoint control technique to prevent ASO destruction of the output transistors.
This IC uses short-circuit braking (lower side output) for motor deceleration during speed switching and lock pull in.
In stop mode, the output is turned off.
If a motor with a coil resistance (interphase) of 10
or lower is used, diodes (rectifying) may be inserted between the
outputs and ground (for all outputs) and current limitation may also be applied during braking to prevent excessive
braking currents. Although this is disadvantageous from an ASO standpoint, since states with a large back EMF are
states with a high switching frequency and the amount of time during which loads are applied to the transistors will
be shorter, ASO problems will not be particular severe.
3. Current limiter circuit
The current limiter circuit is a peak current limiter whose limit current is determined by I = V
RF
/Rf (where VRF = 0.5
V (typical) and Rf is the current detection resistor).
相關PDF資料 |
PDF描述 |
|---|---|
| LB1875 | Polygon Mirror Motor Predriver IC |
| LB1876 | Three-Phase Brushless Motor Driver for Polygon Mirror Motors |
| LB1877 | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
| LB1877M | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
| LB1877V | Brushless Motor Driver with Speed Control for Portable Cassette Recorders |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1875 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Polygon Mirror Motor Predriver IC |
| LB1876 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for Polygon Mirror Motors |
| LB1876(36SOP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference |
| LB1876_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Polygon Mirror Motors 3-phase Brushless Motor Driver |
| LB1876-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。