參數資料
型號: LB8649W
廠商: Sanyo Electric Co.,Ltd.
英文描述: Monolithic Digital IC Digital Camera Motor Driver
中文描述: 單片數字集成電路數碼相機電機驅動器
文件頁數: 5/9頁
文件大小: 138K
代理商: LB8649W
LB8649W
No.7894-5/9
(3) SH/AE system VCM driver constant current control or stepping motor drive
Input
Output
IN9
IN10
IN11
IN12
INHD
OUT9
OUT10
OUT11
OUT12
Vref
ISH
Mode
Low
Low
Low
Low
Standby
High
Low
*
*
High
Low
Low
High
*
*
Low
High
*
*
High
Low
High
Low
*
*
Low
High
Low
Low
High
1.0V
SH & AE
High
Low
*
*
High
Low
Low
High
*
*
Low
High
*
*
High
Low
High
Low
*
*
Low
High
Low
High
Setting
voltage
state
Hold
Low
Low
Low
Low
High
0.67V
Discharged
Standby
Notes
1. "
" indicates the output off state, "*" indicates "Don't care".
2. OUT9 and OUT10 are for SH, and provide stable startup characteristics with fast charge and fast discharge circuits.
3. OUT10 and OUT11 are for AE.
4. In standby mode, the ISH pin voltage is discharged by an internal transistor and thus is set to 0V.
5. Furthermore, the ISH pin is also set to the discharged state when inputs are provided to IN1 through IN8. This is for startup
correction.
6. When INHD is low, the Vref voltage will be 1.0V, and when high, the Vref voltage will be 0.67V.
Notes on Application Design
(1) Constant current level setting (ISH, IAE, RFG1/2, and OUT9 to OUT12)
The constant current level for the OUT9/10 pair is set by the ISH input voltage and the resistor connected to RFG1. As
shown in the block diagram, the current is controlled so that the voltage generated across the current detection resistor
connected between RFG1 and ground and the ISH input voltage become equal. The output current can be determined
from the following equation.
(Output current between OUT9 and OUT10) = (ISH input voltage) ÷ (RFG1 resistance + 0.05
Ω
)
The 0.05
Ω
here is the shared impedance of the emitter of the output transistor that drives the constant current and the
constant current control amplifier's sensing line.
Similarly, the constant current level for the OUT11/12 pair is set by the IAE input voltage and the resistor connected to
RFG2.
Note that since the constant current control block is connected to PGND internally to the IC, if voltage is provided to
ISH and IAE through a voltage divider, the voltage divider resistor ground must be connected to PGND.
(2) Rapid charge and discharge circuits (FC1, OUT9, and OUT10)
The SH control block (OUT9/10) includes rapid charge and rapid discharge circuits to support burst (rapid sequential)
imaging.
Since this type of circuit is not included in the AE control block (OUT11/12), the OUT9/10 block must be used for
shutter drive.
相關PDF資料
PDF描述
LB8652T Monolithic Digital IC Driver for Digital Still Cameras
LB8655T Monolithic Digital IC Driver for Digital Still Cameras
LB8658FN Monolithic Digital IC DSC Motor Driver
LB8681CL Monolithic Digital IC Constant Current Driver IC with H-bridge 】 1.5 Channel
LB8682PL Monolithic Digital IC For Camera Cell Phone Motor Driver Two Saturated Drive Channels and One Constant-Current Drive Channel
相關代理商/技術參數
參數描述
LB8649W-MPB-E 功能描述:馬達/運動/點火控制器和驅動器 DSC MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
LB8649W-TBM-E 功能描述:馬達/運動/點火控制器和驅動器 SYSTEM MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
LB8650T 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Driver for Digital Still Cameras
LB8652LP 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Driver for Digital Still Cameras
LB8652T 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC Driver for Digital Still Cameras