- 您現在的位置：買賣IC網 > PDF目錄30729 > LC0710LG SPECIALTY CONSUMER CIRCUIT, PBGA40 PDF資料下載
參數資料
| 型號： | LC0710LG |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA40 |
| 封裝： | 4.40 X 3.60 MM, FLGA-40 |
| 文件頁數： | 7/22頁 |
| 文件大小： | 426K |
| 代理商： | LC0710LG |
LC72713W
No.6870-15/29
Structure of the Post-Correction Output Data <CCB Interface>
Post-error correction data can be output by using CCB address #FB. Although there are up to 288 bits of valid data that
can be output, it is possible to stop clock input (CL input) and set CE to the low level, and output the remaining data on
the next interrupt with no harmful effects whatsoever.
The maximum amount of data that can be output is 288 bits (36 bytes), and the contents of the status register (STAT)
and the block number register (BLNO) are added as the first two bytes.
The contents of the STAT and BLNO registers are output LSB first.
The post-correction data is output in order starting with the first bit in each single block of data.
The BIC code is not output.
The values of the output data are not guaranteed if multiple data read operations are performed for a single interrupt
signal (INT).
STAT (8 bits)
BLNO (8 bits)
Data section (176 bits) Post-error correction data
Layer 2 CRC (14 bits)
Parity (82 bits)
DO0 to DO7
DO8 to DO15
DO16 to DO191
DO192 to DO205
DO206 to DO287
Layer 4 CRC Check Circuit <CCB Interface>
The basic outline of this operation is the same as that described in the Layer 4 CRC Detection Circuit <Parallel
Interface> section earlier in this document. The data group data used for this error detection operation is sent to the IC
using the CCB interface. The value #FC is used as the CCB address.
The data group data is transferred in 8-bit units. There is no upper limit on the amount of data that can be transferred
(the value N in the figure below), and the data transfer may be divided into multiple operations.
Register Output
The IC internal status and block number registers are special-purpose registers that can be read out by applications. (See
the discussion of the read register data update timing on page 11.)
The application inputs the CCB address #FD to DI. The status register data is output first followed by the block number
register data.
A3
N
N-1
N-2
CR2
CR1
CR0
A2
A1
A0
B3
B2
B1
B0
DI
CL
CE
CRC4 pin output
Note: The number of items, N, refers to
the number of 8-bit items.
CRC4 pin output after N items
have been transferred.
tCRC
tEH
tES
tEL
tCH
tCL
tHD
tSU
A3
BLN7
BLN6
BLN5
ST2
ST1
ST0
A2
A1
A0
B3
B2
B1
B0
DI
DO
CL
CE
tSU
tHD
tCH
tCL
tES
tEL
tDDO
相關PDF資料 |
PDF描述 |
|---|---|
| LC07410LG | SPECIALTY CONSUMER CIRCUIT, PBGA40 |
| LC07410LG | SPECIALTY CONSUMER CIRCUIT, PBGA40 |
| LC074146LP | 1 CHANNEL, AUDIO/VIDEO AMPLIFIER, QCC40 |
| LC074146LP | 1 CHANNEL, AUDIO/VIDEO AMPLIFIER, QCC40 |
| LC19001A010 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC07410LG | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monaural CODEC + Audio I/F + Video Driver |
| LC074146LP | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Monaural CODEC+Audio I/F +Video driver IC |
| LC07422T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Audio CODEC with Video Driver |
| LC07424LP | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Audio CODEC with Video Driver |
| LC07424LP-MPB-E | 功能描述:接口—CODEC RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。