參數資料
型號: LC7218
廠商: Sanyo Electric Co.,Ltd.
英文描述: PLL Frequency Synthesizer for Electronic Tuning in AV Systems
中文描述: 鎖相環頻率合成器的AV系統的電子調諧
文件頁數: 8/16頁
文件大?。?/td> 265K
代理商: LC7218
The LC7218 control data consists of 36 bits. All 36 bits must be input after power is applied to set up the LC7218 initial
state. This is because the last two bits, while being unrelated to user functions, are data that switches the LSI test modes.
Once the LC7218 has been initialized, the contents of the first 24 bits (D
0
to CTEN) can be changed without changing
the contents of the last 12 bits (R0 to T1) by inputting data to DI in serial data input mode.
No. 4758-8/16
LC7218, 7218M, 7218JM
No.
Control block/data
Description
Related data
(1)
(2)
(3)
(4)
Programmable divider
data
D
0
to D
15
Output port data
O
0
to O
6
General-purpose counter
initial data
CTEN
Reference frequency
data
R
0
to R
3
This data sets up the programmable divider.
D
0
to D
15
is a binary value with D
15
as the MSB.
The position of the LSB is changed by DV and SP as listed in the table below.
*
don’t care
When D
4
is the LSB, bits D
0
to D
3
are ignored.
Data that determines the states of the output ports OUT0 to OUT6. O
0
determines the
OUT0 pin output. However, note that when O
0
is 0, OUT0 will output a high level, and when O
0
is 1, OUT0 will output a low level. O
1
to O
6
function in the same manner.
These can be used for a wide range of purposes, including, for example, band switching
signals.
When the TB bit is set to 1, the O
0
data is ignored and the OUT0 pin outputs an 8 Hz clock
time base signal.
Since the output port states are undefined when power is first applied, transfer the control data
quickly.
Data that determines the operation of the general-purpose counter. When CTEN is 0, the 20-bit
binary counter (the general-purpose counter) is reset and the HCTR and LCTR pins are pulled
down to ground. When CTEN is set to 1, the general-purpose counter reset state is cleared and
the counter operates according to the SC bit (the general-purpose selection data). In this state,
the general-purpose counter will count either the HCTR or LCTR input signal.
Since the general-purpose counter is reset by setting CTEN to 0, the result of a count operation
must be sent to the controller while CTEN is still 1.
Data that selects one of the ten LC7218 reference frequencies or sets the LC7218 to
backup mode in which PLL operation is disabled.
Note:
*
PLL inhibit (backup mode)
The programmable divider block is turned off, both the FMIN and AMIN pins are pulled
down to ground, and the charge pump outputs go to the floating state.
DV
SP
TB
SC
SF
GT
DV
SP
LSB
Divisor setting
Actual divisor
1
*
D0
256 to 65536
Twice the set value
0
1
D0
256 to 65536
The set value
0
0
D4
4 to 4096
The set value
R
0
0
R
1
0
R
2
0
R
3
0
Reference frequency (kHz)
100
0
0
0
1
50
0
0
1
0
25
0
0
1
1
25
0
1
0
0
12.5
0
1
0
1
6.25
0
1
1
0
3.125
0
1
1
1
3.125
1
0
0
0
10
1
0
0
1
9
1
0
1
0
5
1
0
1
1
1
1
1
0
0
1
1
0
1
PLL inhibit state
*
1
1
1
0
1
1
1
1
Continued on next page.
相關PDF資料
PDF描述
LC7218M PLL Frequency Synthesizer for Electronic Tuning in AV Systems
LC72191JM PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners
LC72191 PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners
LC72191M PLL Frequency Synthesizer for Electronic Tuning in Car Stereo Tuners
LC7219 PLL Frequency Synthesizers
相關代理商/技術參數
參數描述
LC72-18 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Laser Diode with Monitor Diode
LC72-18G 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Laser Diode with Monitor Diode
LC7218JM 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PLL Frequency Synthesizer for Electronic Tuning in AV Systems
LC7218M 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PLL Frequency Synthesizer for Electronic Tuning in AV Systems
LC7218M-TLM-E 制造商:Sony Semiconductor Solutions Division 功能描述: