- 您現在的位置：買賣IC網 > PDF目錄369721 > LC72319W PDF資料下載
參數資料
| 型號： | LC72319W |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 128K |
| 代理商： | LC72319W |
No. 6650-9/12
LC72314W, 72315W, 72316W
Continued from preceding page.
Pin No.
Pin
I/O
Function
I/O circuit
System reset input.
In CPU operating mode or halt mode, applications must apply a low level for at least
one full machine cycle to reset the system and restart execution with the PC set to
location 0. This pin is connected in parallel with the internal power on reset circuit.
72
RES
I
Output for the 3 V step-up circuit clock. Outputs 1/2 the AM local oscillator frequency
in AM reception mode, and 1/256 the FM local oscillator or 75 kHz in FM reception
mode.
38
VDC1
O
Voltage stepped up by the DC-DC converter (3 V)
May also be used to input an equivalent voltage.
37
VDC3
I
RAM backup power supply. Connected to the VDC3 voltage through a diode.
36
VDDRAM
I
VDC3 voltage adjustment pin. Insert a 10 k
variable resistor between this pin and
ground to adjust the VDC3 voltage.
39
VADJ
O
FM VCO (local oscillator) input.
This pin is selected with the PLL instruction CW1.
The input must be capacitor coupled.
Input is disabled in backup mode, in halt mode, after a reset, and in PLL stop mode.
75
FMIN
I
CMOS amplifier input
AM VCO (local oscillator) input.
This pin and the bandwidth are selected with the PLL instruction CW1.
The input must be capacitor coupled.
Input is disabled in backup mode, in halt mode, after a reset, and in PLL stop mode.
76
AMIN
I
CMOS amplifier input
Dedicated input port for the universal counter.
For frequency measurement, select the HCTR frequency measurement mode and
measurement time with a UCS instruction (b3 = 0, b2 = 0) and start the counter with
a UCC instruction.
When the count operation completes, the CNTEND flag will be set. Since it operates
as an AC amplifier in this mode, the input must be provided through a coupling
capacitor.
Input is disabled in backup mode, HALT mode, after a reset, and in PLL STOP mode.
73
HCTR
I
CMOS amplifier input
Main charge pump output. When the local oscillator frequency divided by N is higher
than the reference frequency a high level is output, when lower, a low level is output,
and the pin is set to the high-impedance state when the frequencies match.
This output goes to the high-impedance state in backup mode, in halt mode, after a
reset, and in PLL stop mode.
78
EO
O
Power supply pin.
This pin must be connected to ground.
This pin must be connected to ground.
This pin must be connected to V
DD
. Supports A/D converter.
—
77
35
74
V
SS
V
SS
V
DD
—
CMOS push-pull
CW1 b1, b0
Input pins
Bandwidth
1
0
AMIN (H)
2 to 20 MHz (SW)
1
1
FMIN (L)
0.5 to 10 MHz (MW, LW)
UCS b3, b2
Input pin measurement mode
0
0
HCTR frequency measurement
0
1
—
1
1
—
UCS b1, b0
Measurement time
0
0
1 ms
0
1
4 ms
1
0
8 ms
1
1
32 ms
Note
*
: When a pin in an I/O switching port is used as an output, applications must first set up the data with an OUT, SPB, or RPB instruction and then set up
output mode with an IOS instruction.
相關PDF資料 |
PDF描述 |
|---|---|
| LC7232 | |
| LC72323-XXX | |
| LC723462W | |
| LC723481W | |
| LC723482W | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC7232 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC72321 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
| LC72321N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC72321N |
| LC72322 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
| LC72322-9271-E | 制造商:ON Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。