- 您現在的位置：買賣IC網 > PDF目錄358759 > LC72321 (Sanyo Electric Co.,Ltd.) Single-Chip Microcontroller with PLL and LCD Driver PDF資料下載
參數資料
| 型號： | LC72321 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Single-Chip Microcontroller with PLL and LCD Driver |
| 中文描述： | 單片微控制器，帶有PLL和LCD驅動器 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 234K |
| 代理商： | LC72321 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁
No. 4796-8/13
LC72321
Continued from preceding page.
Pin
Pin No.
Function
I/O
I/O circuit type
PH0
PH1/BEEP
PH2/DAC1
PH3/DAC2
PI0/S25
PI1/S26
PI2/S27
PI3/S28
S1 to S24
COM1
COM2
FMIN
AMIN
10
9
8
7
39
38
37
36
63 to 40
65
64
74
75
Dedicated output port
Since these pins are high breakdown voltage n-channel
transistor open-drain outputs, they can be effectively used for
functions such as band power supply switching.
Note that PH1 is also used as the BEEP output and that PH2
and PH3 are also used as the DAC1 and DAC2 outputs.
These ports go to the high impedance state during a reset,
i.e., when the RES pin is low, and in BACKUP mode.
Dedicated output port
While these pins have a CMOS output circuit structure, they
can be switched to function as LCD drivers. Their function is
switched by the SS and RS instructions. These pins cannot
be switched individually.
The LCD driver function is selected and a segment off signal
is output when power is first applied or when RES is low.
These pins are held at the low level in BACKUP mode.
Note that when the general-purpose port use option is
specified, these pins output the contents of IPORT when LPC
is 1, and the contents of the general-purpose output port
LATCH when LPC is 0.
LCD driver segment outputs
A frame frequency of 100 Hz and a 1/2 duty, 1/2 bias drive
type are used.
A segment off signal is output when power is first applied or
when RES is low.
These pins are held at the low level in BACKUP mode.
The use of these pins as general-purpose output ports can be
specified as an option.
LCD driver common outputs
A 1/2 duty, 1/2 bias drive type is used.
The output when power is first applied or when RES is low is
identical to the normal operating mode output.
These pins are held at the low level in BACKUP mode.
FM VCO (local oscillator) input
The input must be capacitor-coupled.
The input frequency range is from 10 to 130 MHz.
AM VCO (local oscillator) input
The band supported by this pin can be selected using the PLL
instruction.
High (2 to 40 MHz)
→
SW
Low (0.5 to 10 MHz)
→
LW and MW
Output
Output
Output
Output
Input
Continued on next page.
相關PDF資料 |
PDF描述 |
|---|---|
| LC72322N | Single-Chip Microcontroller with Built-in LCD Driver and PLL Circuits(用于電子調諧的單片微控制器（帶內置LCD驅動器和鎖相環電路 ）) |
| LC72322 | Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323-XXXX | LED RED/AMBR DIFFUSED(WHITE)RND |
| LC72323 | Single-Chip Microcontroller with PLL and LCD Driver |
| LC72323R | Single-Chip Microcontroller with PLL and LCD Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72321N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC72321N |
| LC72322 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
| LC72322-9271-E | 制造商:ON Semiconductor 功能描述: |
| LC72322N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:LC72321N |
| LC72322R | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Microcontroller with PLL and LCD Driver |
發布緊急采購，3分鐘左右您將得到回復。