- 您現在的位置：買賣IC網 > PDF目錄30731 > LC72723 SPECIALTY CONSUMER CIRCUIT, PDIP16 PDF資料下載
參數資料
| 型號： | LC72723 |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP16 |
| 封裝： | DIP-16 |
| 文件頁數： | 7/8頁 |
| 文件大小： | 114K |
| 代理商： | LC72723 |
5.
When switching channels, it is desirable to immediately reset memory and the READY pin with an RST input. If this is not done, data received on the
previous channel may remain in memory. When the IC is reset, data is not written until the RDS-ID is detected, and therefore, the READY signal will go
low after the RDS-ID is detected. (Although the RDS-ID is not output in slave mode, it is detected internally in the IC.) After an RST input, once an RDS-
ID has been detected, all received data will be written to memory regardless of the RDS-ID detection state.
6.
The readout mode may be switched between master and slave modes during readout. Applications must observe the following points to assure data
continuity during this operation.
Data acquisition timing in master mode
Data must be read on the falling edge of RDCL.
Timing of the switch from master mode to slave mode
After the RDCL output goes low and the RDDA data has been acquired, the application must set MODE high immediately. Then, the microcontroller
starts output by setting the RDCL signal low. The microcontroller RDCL output must start within 840 s (tms) after RDCL went low. In this case, if the
last data read in master mode was data item n, then data starting with item n+1 will be written to memory.
Timing of the switch from slave mode to master mode
After all data has been read from memory and READY has gone high, the application must then wait until READY goes low once again the next time
(timing A in the figure), immediately read out one bit of data and input the RDCL clock. Then, at the point READY goes high, the microcontroller must
terminate RDCL output and then set MODE low. The application must switch MODE to low within 840 s (tms) after READY goes low (timing A in the
figure).
No. 6037-7/8
LC72723, LC72723M
RDCL (IC status)
RDCL (microcontroller status)
相關PDF資料 |
PDF描述 |
|---|---|
| LC72723M | SPECIALTY CONSUMER CIRCUIT, PDSO16 |
| LC72723 | SPECIALTY CONSUMER CIRCUIT, PDIP16 |
| LC72F3661 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| LC72F3661 | SPECIALTY CONSUMER CIRCUIT, PQFP80 |
| LC72F3781 | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72723M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:RDS Demodulation IC |
| LC72723MA-AH | 功能描述:調節器/解調器 RoHS:否 制造商:Texas Instruments 封裝 / 箱體:PVQFN-N24 封裝:Reel |
| LC72723MA-ZH | 制造商:ON Semiconductor 功能描述:RDS DEMODULATION IC - Ammo Pack |
| LC72725KM | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:RDS(RBDS) Demodulation IC |
| LC72725KM_10 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:RDS(RBDS) Demodulation IC |
發布緊急采購，3分鐘左右您將得到回復。