No. N7349-3/12
LC75010W
Electrical Characteristics in the Allowable Operating Ranges
Parameter
Symbol
Pin name
Ratings
Unit
min
typ
max
PWDB, RSTB, INTB, CE, CL, DI, TEST0,
High-level input current
IIH
TEST1, TEST2, TEST3, TEST4, TEST5, TEST6,
5
A
TEST7, TEST8, TEST9, TEST10, TEST13, TEST14
PWDB, RSTB, INTB, CE, CL, DI, TEST0,
Low-level input current
IIL
TEST1, TEST2, TEST3, TEST4, TEST5, TEST6,
–5
A
TEST7, TEST8, TEST9, TEST10, TEST13, TEST14
BUSY, DO, TEST11, TEST12 (Microcontroller: 5 V)
4.5
5.5
V
High-level output voltage
VOH
BUSY, DO, TEST11, TEST12 (Microcontroller: 3.3 V)
3.0
3.6
V
Low-level output voltage
VOL
BUSY, DO, TEST11, TEST12
0.5
V
Analog output level
VOUT
AOUT1, AOUT2, AOUT3, AOUT4
0.6
× AVDD5
VP-P
Vref1
Reference voltage output
Vref2
Vref1, Vref2, Vref3
2.35
2.5
2.65
V
Vref3
(Conditions: Audio disabled operating state, Std. board
IAVDD5
installed ; See note)
55
72
mA
AVDD5 = XVDD5 = 5V, DVDD3.3 = 3.3 V
(Conditions: Audio disabled operating state, Std. board
IXVDD5
installed ; See note)
5
7
mA
Current drain
AVDD5 = XVDD5 = 5V, DVDD3.3 = 3.3 V
(Conditions: Audio disabled operating state, Std. board
IDVDD3.3
installed ; See note)
65
85
mA
AVDD5 = XVDD5 = 5V, DVDD3.3 = 3.3 V
(Conditions: Audio disabled operating state, Std. board
Pd
installed ; See note)
515
680
mW
Power dissipation
AVDD5 = XVDD5 = 5V, DVDD3.3 = 3.3 V
Parameter
Conditions
Ratings
Unit
min
typ
max
S/N
A-weighted, Input conditions: 2 Vp-p
85
90
—
dB
Dynamic range
A-weighted
85
90
—
dB
THD+N
Input conditions: 1.5 Vp-p. See note.
—
–86
–80
dB
Conditions: Analog system: 5 V, digital system: 3.3 V, fs: 44.1 kHz, signal frequency: 1 kHz, from the analog source selector input to the
volume control circuit output.
Measurement band: 10 Hz to 20 kHz, using the SANYO-specified DSP evaluation board.
Test circuit: LC75010W external circuit structure with the DSP operating in through mode (4-bit shiftup), room temperature
Test equipment: Audio analyzer (Rohde & Schwarz UPD)
LC75010W Analog Characteristics
Note: THD+N shows the optimal characteristics for an input (1.5 Vp-p) that is 3 dB lower than the full-scale input level.
Parameter
Symbol
Pin name
Ratings
Unit
min
typ
max
Data setup time
tSU
DI, CL
0.75
s
Data hold time
tHD
DI, CL
0.75
s
Clock low-level time
tCL
CL
0.75
s
Clock high-level time
tCH
CL
0.75
s
CE wait time
tEL
CE, CL
0.75
s
CE setup time
tES
CE, CL
0.75
s
CE hold time
tEH
CE, CL
0.75
s
Data latch change time
tLC
0.75
s
Data output time
tDC
DO, CL
0.35
s
tDH
DO, CE
CCB Timing
Note Std. board : 114.3 mm
× 76.2 mm × 1.5 mm, material : glass epoxy resin