- 您現在的位置：買賣IC網 > PDF目錄358763 > LC75347E (Sanyo Electric Co.,Ltd.) Six-Channel Single-Chip Electronic Volume Control System PDF資料下載
參數資料
| 型號： | LC75347E |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Six-Channel Single-Chip Electronic Volume Control System |
| 中文描述： | 六通道單芯片電子音量控制系統 |
| 文件頁數： | 15/17頁 |
| 文件大小： | 602K |
| 代理商： | LC75347E |
No. 7378 -15/17
LC75347E
Usage Notes
1. Data Transmission after Power is First Applied
The states of the internal analog switches are undefined when power is first applied. Applications should set up the
initial data immediately after power is applied (after V
DD
rises above 4.5 V). Applications should also mute the
outputs until the data has been set up and the outputs are stable.
To establish the states of the internal latches, set the bits D64 and D65 to 1 in the first data transferred after power is
first applied.
2. Zero Cross Switching Control
Zero cross switching is used by setting up data in which the zero cross control bits specify zero cross detection mode
(by setting bits D48 to D53 to 0) and transfer that data. Since these control bits are latched first, immediately after the
data is transferred, that is, on the fall of the CE signal, zero cross control can be performed with a single data transfer
operation when updating the volume control settings. If the zero cross control bits specify zero cross detection
disabled mode (by setting bits D48 to D53 to 1), the volume is switched on the fall of the CE signal at the end of the
data transfer.
3. Zero Cross Timer Setting
When the input signal is less than the detection sensitivity of the zero cross comparator, or if only a low-frequency
signal is being input, the state where the IC does not detect a zero cross will continue and the data will not be latched.
The zero cross timer allows applications to set a time at which data will be latched forcibly if the state where no zero
cross is detected continues.
For example, to set a time of 25 ms:
T = 0.69CR
Since the internal pull-up resistor is about 1 M
:
25
×
10
–3
0.69
×
1.0
×
10
6
Applications usually set a time in the range 10 to 50 ms.
4. Notes on Serial Data Transfer
Cover the CL, DI, and CE pin signal lines with the ground pattern, or use shielded cables for these signals so that the
high-frequency digital signals transmitted on these lines do not enter the analog signal system.
C =
0.036
μ
F
相關PDF資料 |
PDF描述 |
|---|---|
| LC75348 | Single-Chip Electronic Volume and Tone Control System |
| LC75348M | Single-Chip Electronic Volume and Tone Control System |
| LC7535M | Electronic Volume/Loudness Control with Serial Data Control and High Voltage-Handling Capacity |
| LC7535P | High-voltage, Two-channel Electronic Attenuator |
| LC75366 | Two-Channel Electronic Volume Control |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC75347E-E | 制造商:ON Semiconductor 功能描述:ELECTRONIC VOLUME - Trays |
| LC75347EH-UC-E | 功能描述:多媒體雜項 RoHS:否 制造商:Texas Instruments 類型: 通道數量: 轉換速率:540 Mbps 分辨率: 封裝 / 箱體:SOIC-16 封裝:Tube |
| LC75348 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Electronic Volume and Tone Control System |
| LC75348M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip Electronic Volume and Tone Control System |
| LC75348M-TLM-E | 功能描述:音頻 DSP RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。