參數資料
型號： LC865624A
廠商： Sanyo Electric Co.,Ltd.
英文描述： 8-Bit Single Chip Microcontroller with On-Chip 24K-Byte ROM and 640-Byte RAM(8位單片微控制器（帶片上24K字節ROM和640字節RAM）)
中文描述： 8位單片機微控制器的片上足金字節ROM和640字節的RAM（8位單片微控制器（帶片上ROM的足金字節和640字節的RAM））
文件頁數： 3/20頁
文件大?。?/td> 643K
代理商： LC865624A
LC865632/28/24/20/16/12/08A
3/20
(11) Interrupts system
- 13-sources 10-vectored interrupts :
1. External interrupt INT0 (include watchdog timer)
2. External interrupt INT1
3. External interrupt INT2, timer / counter T0L (Lower 8 bits)
4. External interrupt INT3, base timer
5. Timer / counter T0H (Upper 8-bit)
6. Timer T1L, Timer T1H
7. Serial interface SIO0
8. Serial interface SIO1
9. AD converter
10. Port 0
- Built-in interrupt priority control register
Microcontroller allows 3 levels of interrupt; low level, high level, and highest level of multiplex interrupt. It can specify
a low level or a high level interrupt priority from INT2/T0L through port 0 (i.e. the above interrupt number from three
through ten). It can also specify a low level or the highest level interrupt priority to INT0 and INT1.
(12) Real-time service operation
The Real-Time Service (RTS) functions the 4-byte data-transfer between the Special Function Registers at acknowledging
the interrupt request.
The RTS starts within 1 instruction cycle-time and completes within 5 instructions cycle-time after occurring the interrupt
request.
(13) Sub-routine stack levels
- 128 levels (Max.) : stack area included in RAM area
(14) Multiplication and division
- 16 bits × 8-bit (7 instruction cycle times)
- 16 bits ÷ 8-bit (7 instruction cycle times)
(15) Three oscillation circuits
- On-chip RC oscillation circuit using for the system clock
- On-chip CR oscillation circuit using for the system clock
- On-chip crystal oscillation circuit using for the system clock and for time-base clock
XT1 terminal can be used as P74
(16) Standby function
- HALT mode function
The HALT mode is used to reduce the power dissipation. In this operation mode, the program execution is stopped. This
operation mode can be released by the interrupt request signals or the initial system reset request signal.
- HOLD mode function
The HOLD mode is used to freeze all the oscillations ;
RC (internal), CF and Crystal oscillations. This mode can be released by the following operations.
Reset terminal ( RES) set to low level
P70/INT0, P71/INT1 terminals set to assigned level (programmable)
Input a Port 0 interrupt condition
(17) Factory shipment
DIP64S, QFP64E delivery form
(18) Development support tools
- Evaluation (EVA) chip
: LC866098
- EPROM version
: LC86E5632
- One time version
: LC86P5632
- Emulator
: EVA86000 + ECB866600 (Evaluation chip board)
+ POD865000 (Pod for DIP64S)
+ POD865010 (Pod for QFP64E)
相關PDF資料
PDF描述
LC866008A 8-bit single chip microcomputer
LC866008 8-Bit Single Chip Microcontroller with One-Time PROM
LC866028B 8-bit single chip microcomputer
LC866116A Octal Bus Transceivers With 3-State Outputs 20-TVSOP -40 to 85
LC866128A Octal Bus Transceivers With 3-State Outputs 20-TVSOP -40 to 85
相關代理商/技術參數
參數描述
LC865628 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with One-Time Programmable PROM
LC865628A 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller
LC865632 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller with One-Time Programmable PROM
LC865632A 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller
LC866000A 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS 8-Bit Single-Chip Microcomputers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*