- 您現在的位置：買賣IC網 > PDF目錄358772 > LC9947G (Sanyo Electric Co.,Ltd.) 1/5-Inch Optical Size EIA Black-and-White Solid-State Imaging Device(1/5英寸光型EIA黑白固態圖象設備) PDF資料下載
參數資料
| 型號： | LC9947G |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | 1/5-Inch Optical Size EIA Black-and-White Solid-State Imaging Device(1/5英寸光型EIA黑白固態圖象設備) |
| 中文描述： | 1/5-Inch光學尺寸環評黑與白固態成像設備（1 / 5英寸光型環評黑白固態圖象設備） |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 73K |
| 代理商： | LC9947G |
Test Methods
The following tests are performed with the CCD device to be measured mounted on the Sanyo evaluation board.
1. Sensitivity
Set up a CCV31F pattern box (Dai Nippon Printing Co., Ltd., intensity: 1320 NT, color temperature: 3100°K) with
no pattern, and take an image with C-500 a 1 mm thickness infrared blocking filter mounted in front of a Fujinon
HF16A lens. Set the lens aperture to f11, and set the separation between the lens and the pattern box to be 50 cm.
Measure the CCD output signal from the center of the image in this state.
2. Video signal non-uniformity
Test this item under the following conditions.
Standard drive state (See the specifications document.)
Use a halogen lamp with a color temperature of 3200°K as the light source.
Use an infrared blocking filter (C-500, 1 mm thickness).
Set the CCD surface illumination level to be 7 lux, and divide the screen into 45 blocks as shown in Figure 3.
Measure the average value in each block and determine the maximum, minimum, and mean of those values.
Determine the ratio of the difference between the maximum and minimum of the block averages to the mean of the
block averages.
VF =
Fig. 3
3. Saturated signal level
In the test method 1 setup state, remove the lens to saturate the output signal. Measure the CCD output signal from
the center of the image at this time.
4. Smear
Place a 1/10 V chart in front of a halogen light source as described below and take the image.
Adjust the image (input) light intensity using ND filters so that the output signal at point A, i.e., the CCD output,
becomes 250 mV.
Remove the ND filter and measure the output value for the first line (at point B) in the CCD output signal.
Fig. 4
(block average maximum) – (block average minimum)
(block average mean)
No. 4971-6/9
LC9947G
SM =
×
100 (%)
VB:
TND: Transmittance of the ND filter
The amount of smear (mV) at point B
VB
×
TND
250
Point B
Point
A
相關PDF資料 |
PDF描述 |
|---|---|
| LC9948G | 1/5 Optical Size CCIR B/W Solid-State Image Sensor |
| LC9949G | 1/6 Optical Size EIA B/W Solid-State Image Sensor |
| LC9997 | 1/5 Inch Optical Size NTSC Color Solid-State Image Device |
| LC9997G | 1/5 Inch Optical Size NTSC Color Solid-State Image Device |
| LC9997M | 1/5-Inch Frame Transfer CCD NTSC Color Image Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC9948G | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/5 Optical Size CCIR B/W Solid-State Image Sensor |
| LC9949G | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1/6 Optical Size EIA B/W Solid-State Image Sensor |
| LC99501-RB5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Video Camera Circuit |
| LC9965 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LC9967 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
發布緊急采購，3分鐘左右您將得到回復。