
Microsemi
Scottsdale Division
8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503
Page 1
Copyright
2001
MSCXXXX.PDF 7-26 2002 REV 0
W
M
.
C
LCV01-6
Bidirectional TVS Array
SCOTTSDALE
DIVISION
L
DE S CRIPT ION
This 16 pin one-line pair, bi-directional, LOW CAPACITANCE array is designed for
use in applications where protection is required at the board level. It provides
protection from voltage transients caused by electrostatic discharge (ESD) as
defined in IEC 61000-4-2, electrical fast transients (EFT) per IEC 61000-4-4 and
effects of secondary lightning as stated by IEC 61000-4-5.
These TRANSIENT VOLTAGE SUPPRESSOR (TVS) arrays have a peak pulse
power rating of 1500 watts for a 10/1000
μ
sec pulse and are designed to be used for
secondary surge protection on high-speed telecommunications lines. This device
can be used in either common or differential mode applications. It is typically used
between Tip and Ring. Applications include T1/E1 and DSL interfaces in base
stations, routers, and long-haul transient immunity requirement per Bellcore 1089,
FCC Part 68 (type A and B surges and IEC 61000-4-5
:
E LE CT R ICAL CHAR ACT E R IS T ICS PE R LINE PAIR @ 25°C Unless otherw ise spec ified
STAND OFF
VOLTAGE
V
WM
VOLTS
BREAKDOWN
VOLTAGE
V
@1 mA
VOLTS
CLAMPING
VOLTAGE
V
@ 100 Amp
(Figure 2)
VOLTS
CLAMPING
VOLTAGE
V
@ 200 Amp
(Figure 3)
VOLTS
STANDBY
CURRENT
I
D
@ V
WM
μA
CAPACITANCE
(f=1 MHz)
C
@0V
pF
PART
NUMBER
DEVICE
MARKING
MAX
MIN
MAX
MAX
MAX
TYP
LCV01-6
LCV01-6
6.0
8.0
15
21
2
90
Note: Transient Voltage Suppressor (TVS) product is normally selected based on its stand off voltage V
WM
. Product selected
voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected.
T V S array
APPL IC AT IONS
T1/E1 line cards
Base stations
WAN interfaces
XDSL interfaces
CSU/DSU equipment
F E A T U R E S
1500 watts peak pulse power
Protects one-line pair
Provides electrically isolated protection
SO-16W package
UL 94V-0 flamability classification
LOW CAPACITANCE 90 pF per line pair
M A X I M U M R A T I N G S
Operating temperature: -55°C to +150°C
Storage temperature: -55°C to +150°C
Peak pulse power: 1500 watts (10/1000 μs, Fig 1)
Pulse repetition rate: < .01%
Thermal resistance:< 30°C/watt (junction-to-case)
Lead soldering temperature: 260°C, 10s maximum
M E C H A N I C A L
Molded SO-16W Surface Mount
Weight 0.25 grams (approximate)
Marking: Logo, device marking code, date code
Pin #1 defined by dot on top of package
P A C K A G I N G
Tape & Reel per EIA Standard 481
13 inch reel; 2,500 pieces (OPTIONAL)
Carrier tubes; 45 pcs (STANDARD)
IMPORTANT:
For the most current data, consult
MICROSEMI
’s website at:
http://www.microsemi.com