參數資料
型號： LFEC1E-4TN144C
廠商： Lattice Semiconductor Corporation
文件頁數： 93/163頁
文件大?。?/td> 0K
描述： IC FPGA 1.5KLUTS 97I/O 144-TQFP
標準包裝： 60
系列： EC
邏輯元件/單元數： 1500
RAM 位總計： 18432
輸入/輸出數： 97
電源電壓： 1.14 V ~ 1.26 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 144-LQFP
供應商設備封裝： 144-TQFP（20x20）
其它名稱： 220-1772
LFEC1E-4TN144C-ND
2-32
Architecture
LatticeECP/EC Family Data Sheet
be shifted in and loaded directly onto test nodes, or test data to be captured and shifted out for verification. The test
access port consists of dedicated I/Os: TDI, TDO, TCK and TMS. The test access port has its own supply voltage
VCCJ and can operate with LVCMOS3.3, 2.5, 1.8, 1.5 and 1.2 standards.
For more details on boundary scan test, please see information regarding additional technical documentation at
the end of this data sheet.
Device Configuration
All LatticeECP/EC devices contain two possible ports that can be used for device configuration. The test access
port (TAP), which supports bit-wide configuration, and the sysCONFIG port that supports both byte-wide and serial
configuration.
The TAP supports both the IEEE Std. 1149.1 Boundary Scan specification and the IEEE Std. 1532 In-System Con-
figuration specification. The sysCONFIG port is a 20-pin interface with six of the I/Os used as dedicated pins and
the rest being dual-use pins (please refer to TN1053 for more information about using the dual-use pins as general
purpose I/O). There are four configuration options for LatticeECP/EC devices:
1.
Industry standard SPI memories.
2.
Industry standard byte wide flash and ispMACH 4000 for control/addressing.
3.
Configuration from system microprocessor via the configuration bus or TAP.
4.
Industry standard FPGA board memory.
On power-up, the FPGA SRAM is ready to be configured with the sysCONFIG port active. The IEEE 1149.1 serial
mode can be activated any time after power-up by sending the appropriate command through the TAP port. Once a
configuration port is selected, that port is locked and another configuration port cannot be activated until the next
power-up sequence.
For more information about device configuration, please see the list of technical documentation at the end of this
data sheet.
Internal Logic Analyzer Capability (ispTRACY)
All LatticeECP/EC devices support an internal logic analyzer diagnostic feature. The diagnostic features provide
capabilities similar to an external logic analyzer, such as programmable event and trigger condition and deep trace
memory. This feature is enabled by Lattice’s ispTRACY. The ispTRACY utility is added into the user design at com-
pile time.
For more information about ispTRACY, please see information regarding additional technical documentation at the
end of this data sheet.
External Resistor
LatticeECP/EC devices require a single external, 10K ohm +/- 1% value between the XRES pin and ground. Device
configuration will not be completed if this resistor is missing. There is no boundary scan register on the external
resistor pad.
相關PDF資料
PDF描述
IR2156S IC CNTL BALLAST 600V 0.5A 14SOIC
RSA30DTBT-S664 CONN EDGECARD 60POS R/A .125 SLD
F931A156MAA CAP TANT 15UF 10V 20% 1206
MC78M15CT IC REG LDO 15V .5A TO-220
RMA30DTBT-S664 CONN EDGECARD 60POS R/A .125 SLD
相關代理商/技術參數
參數描述
LFEC1E-4TN144I 功能描述:FPGA - 現場可編程門陣列 1.5K LUTs 97 IO 1.2V -4 Spd I RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
LFEC1E-5F256C 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
LFEC1E-5F256I 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
LFEC1E-5F484C 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
LFEC1E-5F484I 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*