參數資料
型號： LFEC6E-3QN208C
廠商： Lattice Semiconductor Corporation
文件頁數： 129/163頁
文件大?。?/td> 0K
描述： IC FPGA 6.1KLUTS 147I/O 208-PQFP
標準包裝： 24
系列： EC
邏輯元件/單元數： 6100
RAM 位總計： 94208
輸入/輸出數： 147
電源電壓： 1.14 V ~ 1.26 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 208-BFQFP
供應商設備封裝： 208-PQFP（28x28）
4-2
Pinout Information
LatticeECP/EC Family Data Sheet
TDI
I
Test Data in pin. Used to load data into device using 1149.1 state machine.
After power-up, this TAP port can be activated for configuration by sending
appropriate command. (Note: once a configuration port is selected it is
locked. Another configuration port cannot be selected until the power-up
sequence). Pull-up is enabled during configuration.
TDO
O
Output pin. Test Data out pin used to shift data out of device using 1149.1.
VCCJ
—VCCJ - The power supply pin for JTAG Test Access Port.
Configuration Pads (used during sysCONFIG)
CFG[2:0]
I
Mode pins used to specify configuration modes values latched on rising edge
of INITN. During configuration, a pull-up is enabled. These are dedicated
pins.
INITN
I/O
Open Drain pin. Indicates the FPGA is ready to be configured. During config-
uration, a pull-up is enabled. It is a dedicated pin.
PROGRAMN
I
Initiates configuration sequence when asserted low. This pin always has an
active pull-up. This is a dedicated pin.
DONE
I/O
Open Drain pin. Indicates that the configuration sequence is complete, and
the startup sequence is in progress. This is a dedicated pin.
CCLK
I/O
Configuration Clock for configuring an FPGA in sysCONFIG mode.
BUSY/SISPI
I/O
Read control command in SPI3 or SPIX mode.
CSN
I
sysCONFIG chip select (Active low). During configuration, a pull-up is
enabled.
CS1N
I
sysCONFIG chip select (Active low). During configuration, a pull-up is
enabled.
WRITEN
I
Write Data on Parallel port (Active low).
D[7:0]/SPID[0:7]
I/O
sysCONFIG Port Data I/O.
DOUT/CSON
O
Output for serial configuration data (rising edge of CCLK) when using sys-
CONFIG port.
DI/CSSPIN
I/O
Input for serial configuration data (clocked with CCLK) when using sysCON-
FIG port. During configuration, a pull-up is enabled. Output when used in
SPI/SPIX modes.
Signal Descriptions (Cont.)
Signal Name
I/O
Description
相關PDF資料
PDF描述
LFEC6E-3Q208C IC FPGA 6.1KLUTS 147I/O 208-PQFP
RMM40DTAT CONN EDGECARD 80POS R/A .156 SLD
LFXP3E-5Q208C IC FPGA 3.1KLUTS 136I/O 208-PQFP
RGM40DTAT CONN EDGECARD 80POS R/A .156 SLD
ADATE302-02BSVZ IC DCL ATE 500MHZ DUAL 100TQFP
相關代理商/技術參數
參數描述
LFEC6E-3QN208I 功能描述:FPGA - 現場可編程門陣列 6.1 LUT 147 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
LFEC6E-3T100C 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
LFEC6E-3T100I 制造商:LATTICE 制造商全稱:Lattice Semiconductor 功能描述:LatticeECP/EC Family Data Sheet
LFEC6E-3T144C 功能描述:FPGA - 現場可編程門陣列 1.2V 97 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
LFEC6E-3T144I 功能描述:FPGA - 現場可編程門陣列 6.1 LUT 97 I/O RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*