![](http://datasheet.mmic.net.cn/330000/LH1262CACTR_datasheet_16423623/LH1262CACTR_2.png)
LH1262CAC, LH1262CACTR, LH1262CB
www.vishay.com
Vishay Semiconductors
Rev. 1.4, 26-Sep-11
2
Document Number: 83802
For technical questions, contact:
optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc91000
Notes
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
(1)
Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through
hole devices (DIP).
Note
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
Note
(1)
f = 1.0 kHz, pulse width = 100 μs, load (R
L
) = 1.0 M
Ω
, 15 pF; measured at 90 % rated voltage (t
on
), 10 % rated voltage (t
off
). Actuation speed
depends upon the external t
on
and t
off
circuitry and the capacitance of the MOSFET.
FUNCTIONAL DESCRIPTION
Figure 1 outlines the IV characteristics of the illuminated photodiode array (PDA). For operation at voltages below V
OC
, the PDA
acts as a nearly constant current source. The actual region of operation depends upon the load.
The amount of current applied to the LED (pins 1 and 2 or 3 and 4) determines the amount of light produced for the PDA. For
high temperature operation, more LED current may be required.
ABSOLUTE MAXIMUM RATINGS
(T
amb
= 25 °C, unless otherwise specified)
PARAMETER
SSR
LED input ratings continuous forward current
LED input ratings reverse voltage
Photodiode array reverse voltage
Ambient operating temperature range
Storage temperature range
Pin soldering time
(1)
Input to output isolation voltage
TEST CONDITION
SYMBOL
VALUE
UNIT
I
F
V
R
V
R
T
amb
T
stg
T
S
V
ISO
50
5.0
100
mA
V
V
°C
°C
°C
V
RMS
I
R
≤
10 μA
I
R
≤
2.0 μA
- 40 to + 85
- 40 to + 150
270
5300
t = 7.0 s max.
t = 60 s min.
ELECTRICAL CHARACTERISTICS
(T
amb
= 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
LED forward voltage
I
F
= 10 mA
Detector forward voltage
I
F
= 10 μA
Detector reverse voltage
I
R
= 2.0 μA
I
F
= 5.0 mA
I
F
= 10 mA
I
F
= 20 mA
I
F
= 5.0 mA
I
F
= 10 mA
I
F
= 20 mA
SYMBOL
V
F
V
F(PDA)
V
R(PDA)
V
OC
V
OC
V
OC
I
SC
I
SC
I
SC
MIN.
1.15
TYP.
1.26
14
200
12.95
13.45
13.92
1.6
3.4
6.9
MAX.
1.45
UNIT
V
V
V
V
V
V
μA
μA
μA
Open circuit voltage (pins 5, 6 or 7, 8)
10
15
Short circuit current (pins 5, 6 or 7, 8)
1.0
2.6
6.5
14
SWITCHING CHARACTERISTICS
(T
amb
= 25 °C, unless otherwise specified)
PARAMETER
Turn-on time
Turn-off time
TEST CONDITION
I
F
= 20 mA
(1)
I
F
= 20 mA
(1)
SYMBOL
t
on
t
off
MIN.
TYP.
35
90
MAX.
UNIT
μs
μs