- 您現在的位置：買賣IC網 > PDF目錄377641 > LH1525ACD (VISHAY SEMICONDUCTORS) Solid State Relay, 1 Form A Solid State Relays PDF資料下載
參數資料
| 型號： | LH1525ACD |
| 廠商： | VISHAY SEMICONDUCTORS |
| 元件分類： | 特殊繼電器 |
| 英文描述： | Solid State Relay, 1 Form A Solid State Relays |
| 中文描述： | Solid State Relays Normally Open Form 1A 400V |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 147K |
| 代理商： | LH1525ACD |
LH1525AT, LH1525AAB, LH1525AABTR
Vishay Semiconductors
www.vishay.com
Rev. 1.9, 21-Aug-12
7
Document Number: 83823
For technical questions, contact:
optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc91000
APPLICATIONS
INPUT CONTROL
The LH1525 low turn-on current SSR has highly sensitive
photodetection circuits that will detect even the most minute
currents flowing through the LED. Leakage current must be
considered when designing a circuit to turn on and off these
relays.
Figure 23 shows a typical logic circuit for providing LED
drive current. R
1
is the input resistor that limits the amount
of current flowing through the LED. For 5 V operation, a
2700
Ω
resistor will limit the drive current to about 1.4 mA.
Where high-speed actuation is desirable, use a lower value
resistor for R
1
. An additional RC peaking circuit is not
required with the LH1525 relay.
R
2
is an optional pull-up resistor which pulls the logic level
high output (V
OH
) up toward the VS potential. The pull-up
resistance is set at a high value to minimize the overall
current drawn from the VS. The primary purpose of this
resistor is to keep the differential voltage across the LED
below its turn-on threshold. LED dropout voltage is graphed
vs. temperature in the typical performance characteristics
section. When the logic gate is high, leakage current will flow
through R
2
. R
2
will draw up to 8 mA before developing a
voltage potential which may possibly turn on the LED.
Each application should be evaluated, over the full operating
temperature range to make sure that leakage current
through the input control LED is kept to a value less than the
minimum LED forward current for switch turn-off
specification.
Fig. 23 - Input Control Circuit
PACKAGE DIMENSIONS
in millimeters
ilh1525at_22
VS
Any TTL or
buffered CMOS
logic
R1
2700
Ω
R2
100 k
Ω
SSR
0.35
0.25
3.81
2.79
3.81
3.30
0.051 min.
7.62 typ.
0.9
0.8
2.54 typ.
1 min.
0.55
0.45
6.5
6.3
8.7
8.5
Pin one ID
6
5
4
1
2
3
18° typ.
8.82
7.62
4° typ.
DIP
ISO method A
i178001
相關PDF資料 |
PDF描述 |
|---|---|
| LH1525AT | Relay SSR 50mA 1.4V DC-IN 0.25A 400V AC/DC-OUT 6-Pin PDIP Tube |
| LH1525AAB | Relay SSR 50mA 1.4V DC-IN 0.25A 400V AC/DC-OUT 6-Pin PDIP SMD Tube |
| LH1525ACDTR | OPTICAL ISOLATORS - COMPONENT |
| LH1526AAC | Relay SSR 50mA 1.4V DC-IN 0.25A 400V AC/DC-OUT 8-Pin PDIP SMD Tube |
| LH1526AB | Relay SSR 50mA 1.4V DC-IN 0.25A 400V AC/DC-OUT 8-Pin PDIP Tube |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LH1525ACDTR | 功能描述:固態繼電器-PCB安裝 Normally Open Form 1A 400V RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| LH1525AT | 功能描述:固態繼電器-PCB安裝 Normally Open Form 1A RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| LH1525AT | 制造商:Vishay Semiconductors 功能描述:SOLID STATE RELAY |
| LH1525AT_11 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:1 Form A Solid-State Relay |
| LH1526 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:1 Form C |
發布緊急采購，3分鐘左右您將得到回復。