- 您現在的位置：買賣IC網 > PDF目錄2002 > LICAL-ENC-MS001 (Linx Technologies Inc)IC ENCODER MS SERIES 20-SSOP PDF資料下載
參數資料
| 型號： | LICAL-ENC-MS001 |
| 廠商： | Linx Technologies Inc |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ENCODER MS SERIES 20-SSOP |
| 標準包裝： | 1,600 |
| 系列： | MS |
| 類型： | 數據編碼器 |
| 應用： | 警報系統(tǒng)，通信系統(tǒng) |
| 電壓 - 電源，模擬： | 2.0 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
–
14
Application Example
The MS encoder is ideal for registering button presses in remote control
applications. An example application circuit is shown in the figure below.
In this circuit, SPDT switches are used to select the baud rate so that
pull-down resistors are not needed. The data lines are connected to
buttons and when any button is pressed, the SEND line is pulled high and
causes the encoder to transmit. The diodes are used to prevent the voltage
on one data line from appearing on another data line.
If only one data line is needed, then it can be tied directly to the SEND line
without the need for the diodes.
None of the inputs have pull-up or pull-down resistors internally, so 100k
Ω
pulldown resistors are used on the data lines, SEND, and CREATE_ADDR.
These resistors are used to pull the lines to ground when the buttons are
not being pressed and ensure that they are always in a known state and
not floating. Without these resistors, the state of the lines could not be
guaranteed and encoder operation may not be predictable.
A LED indicator is attached to the MODE_IND line to provide visual
feedback to the user that an operation is taking place. This line will
source a maximum of 25mA, so the limiting resistor may not be needed,
depending on the LED chosen and the brightness desired.
Outgoing encoded data will be sent out of the DATA_OUT line at the
baud rate determined by the state of the SEL_BAUD lines. This line can
be connected directly to the DATA_IN line of a Linx transmitter, used to
modulate an infrared diode, or connected to any other serial transmission
medium.
To Transmitter
100k
220
100k
LICAL-ENC-MS001
D6
D7
SEL_BAUD0
SEL_BAUD1
GND
TX_CNTL
DATA_OUT
MODE_IND
D5
D4
D3
D2
VCC
D1
D0
SEND
CREATE_ADDR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
220
To Transmitter PDN
100k
Figure 13: MS Series Encoder Application Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| LICAL-TRC-MT | IC TRANSCODER MT BI-DIR 20-SSOP |
| LT1331CNW#PBF | IC TXRX 5V/3V RS232 28-DIP |
| LT1341CG#TRPBF | IC TXRX 5V RS232 SHUTDOWN 28SSOP |
| LT1342CG | IC TXRX 5V RS232 W/3VLOGC 28SSOP |
| LT1794CSW#PBF | IC OPAMP 200MHZ DUAL 20-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LICAL-TRC-MT | 功能描述:編碼器、解碼器、復用器和解復用器 MT Series Transcoder RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| LI-CAM-AR0331 | 功能描述:視頻模塊 Aptina AR0331 HD WDR CAMERA BOARD RoHS:否 制造商:Leopard Imaging 產品:Camera Modules 支持的視頻格式:H.264, MPEG4, MJPEG 每秒幀數:30 顯示分辨率—像素:1920 x 1080 接口類型:RS-485, USB 工作電源電壓:12 V 最大工作溫度:+ 45 C 尺寸:113.3 mm x 57.6 mm x 32.2 mm |
| LI-CAM-AR0331-324-1.8 | 功能描述:視頻模塊 Aptina AR0331 IP CAMERA BOARD RoHS:否 制造商:Leopard Imaging 產品:Camera Modules 支持的視頻格式:H.264, MPEG4, MJPEG 每秒幀數:30 顯示分辨率—像素:1920 x 1080 接口類型:RS-485, USB 工作電源電壓:12 V 最大工作溫度:+ 45 C 尺寸:113.3 mm x 57.6 mm x 32.2 mm |
| LI-CAMFLEX | 功能描述:程序設計器配件 2" CAMERA EXTENSION CABLE RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming |
| LI-CAM-IMX036 | 功能描述:視頻模塊 Sony iMX036 HD IP CAMERA BOARD RoHS:否 制造商:Leopard Imaging 產品:Camera Modules 支持的視頻格式:H.264, MPEG4, MJPEG 每秒幀數:30 顯示分辨率—像素:1920 x 1080 接口類型:RS-485, USB 工作電源電壓:12 V 最大工作溫度:+ 45 C 尺寸:113.3 mm x 57.6 mm x 32.2 mm |
發(fā)布緊急采購，3分鐘左右您將得到回復。