- 您現在的位置：買賣IC網 > PDF目錄383283 > LIS244AL (意法半導體) MEMS motion sensor:2-axis - 【2g ultracompact linear accelerometer PDF資料下載
參數資料
| 型號： | LIS244AL |
| 廠商： | 意法半導體 |
| 英文描述： | MEMS motion sensor:2-axis - 【2g ultracompact linear accelerometer |
| 中文描述： | MEMS運動傳感器:2 -軸- 【第二代超小型線性加速度計 |
| 文件頁數： | 8/15頁 |
| 文件大小： | 149K |
| 代理商： | LIS244AL |
Mechanical and electrical specifications
LIS244AL
8/15
Self Test
allows to test the mechanical and electric part of the sensor, allowing the seismic
mass to be moved by means of an electrostatic test-force. The Self Test function is off when
the ST pin is connected to GND. When the ST pin is tied at Vdd an actuation force is applied
to the sensor, simulating a definite input acceleration. In this case the sensor outputs will
exhibit a voltage change in their DC levels which is depending on the supply voltage through
the device sensitivity. When ST is activated, the device output level is given by the algebraic
sum of the signals produced by the acceleration acting on the sensor and by the
electrostatic test-force. If the output signals change within the amplitude specified inside
Table 3
, than the sensor is working properly and the parameters of the interface chip are
within the defined specification.
Output impedance
describes the resistor inside the output stage of each channel. This
resistor is part of a filter consisting of an external capacitor of at least 2.5nF and the internal
resistor. Due to the resistor level, only small inexpensive external capacitors are needed to
generate low corner frequencies. When interfacing with an ADC it is important to use high
input impedance input circuitries to avoid measurement errors. Note that the minimum load
capacitance forms a corner frequency close to the resonance frequency of the sensor. In
general the smallest possible bandwidth for a particular application should be chosen to get
the best results.
相關PDF資料 |
PDF描述 |
|---|---|
| LIS244ALTR | MEMS motion sensor:2-axis - 【2g ultracompact linear accelerometer |
| LIS2L02AQ3 | MEMS INERTIAL SENSOR: 2-axis - 【2g/【6g LINEAR ACCELEROMETER |
| LIS2L02AQ3TR | MEMS INERTIAL SENSOR: 2-axis - 【2g/【6g LINEAR ACCELEROMETER |
| LIS302ALB | MEMS motion sensor 3-axis - 【2g analog output piccolo accelerometer |
| LIS302ALBTR | MEMS motion sensor 3-axis - 【2g analog output piccolo accelerometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS244ALH | 功能描述:加速計 - 板上安裝 MEMS Inertial High Pef 2-Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS244ALHTR | 功能描述:加速計 - 板上安裝 MEMS Inertial High Pef 2-Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS244ALTR | 功能描述:加速計 - 板上安裝 MEMS motion snsr 2 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS2DE12TR | 功能描述:Accelerometer X, Y, Z Axis ±2g, 4g, 8g, 16g 0.5Hz ~ 2.69kHz 12-LGA (2x2) 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:數字 軸:X，Y，Z 加速度范圍:±2g，4g，8g，16g 靈敏度（LSB/g）:64（±2g）~ 5（±16g） 靈敏度（mV/g）:- 帶寬:0.5Hz ~ 2.69kHz 輸出類型:I2C，SPI 電壓 - 電源:1.71 V ~ 3.6 V 特性:可調帶寬，可選量程，溫度傳感器 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:12-VFLGA 供應商器件封裝:12-LGA（2x2） 標準包裝:1 |
| LIS2DH | 制造商:STMicroelectronics 功能描述:ACCELEROMETER DUAL - Bulk |
發布緊急采購，3分鐘左右您將得到回復。