- 您現在的位置：買賣IC網 > PDF目錄30742 > LIS302ALB (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PQCC14 PDF資料下載
參數資料
| 型號： | LIS302ALB |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| 封裝： | 3 X 5 MM, 0.92 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, TLGA-14 |
| 文件頁數： | 16/17頁 |
| 文件大?。?/td> | 235K |
| 代理商： | LIS302ALB |
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
Mechanical and electrical specifications
LIS302ALB
8/17
over lifetime. The Zero-g level tolerance describes the range of Zero-g levels of a population
of sensors.
Self Test allows to check the sensor functionality without moving it. The Self Test function is
off when the ST pin is connected to GND. When the ST pin is tied at Vdd an actuation force
is applied to the sensor, simulating a definite input acceleration. In this case the sensor
outputs will exhibit a voltage change in their DC levels which is related to the selected full
scale and depending on the Supply Voltage through the device sensitivity. When ST is
activated, the device output level is given by the algebraic sum of the signals produced by
the acceleration acting on the sensor and by the electrostatic test-force. If the output signals
change within the amplitude specified inside Table 2, than the sensor is working properly
and the parameters of the interface chip are within the defined specification.
Output impedance describes the resistor inside the output stage of each channel. This
resistor is part of a filter consisting of an external capacitor of at least 2.5nF and the internal
resistor. Due to the resistor level, only small inexpensive external capacitors are needed to
generate low corner frequencies. When interfacing with an ADC it is important to use high
input impedance input circuitries to avoid measurement errors. Note that the minimum load
capacitance forms a corner frequency close to the resonance frequency of the sensor. In
general the smallest possible bandwidth for a particular application should be chosen to get
the best results.
相關PDF資料 |
PDF描述 |
|---|---|
| LIS302ALBTR | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS3L02AS4 | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| LM0555N | PULSE; RECTANGULAR, TIMER, PDIP8 |
| LM1035N | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP20 |
| LM1040N | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS302ALBTR | 功能描述:加速計 - 板上安裝 MEMS Motion Sensor RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302ALK | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS motion sensor 3-axis-【2g analog output "piccolo" accelerometer |
| LIS302ALKTR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS motion sensor 3-axis-【2g analog output "piccolo" accelerometer |
| LIS302DL | 功能描述:加速計 - 板上安裝 MEMS motion snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302DL_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS motion sensor 3-axis - 【2g/【8g smart digital output “piccolo” accelerometer |
發布緊急采購，3分鐘左右您將得到回復。