- 您現在的位置：買賣IC網 > PDF目錄43920 > LIS3L02AQ (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, QCC44 PDF資料下載
參數資料
| 型號： | LIS3L02AQ |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QCC44 |
| 封裝： | 7 X 7 MM, 1.80 MM HEIGHT, PLASTIC, QFN-44 |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 177K |
| 代理商： | LIS3L02AQ |
Obsolete
Product(s)
- Obsolete
Product(s)
LIS3L02AQ
6/9
The nominal value of the capacitors, at steady state, is few pF and when an acceleration is applied the maximum
variation of the capacitive load is few hundredths of pF.
3.2 IC Interface
The complete signal processing uses a fully differential structure, while the final stage converts the differential
signal into a single-ended one to be compatible with the external world.
The first stage is a low-noise capacitive amplifier that implements a Correlated Double Sampling (CDS) at its
output to cancel the offset and the 1/f noise. The produced signal is then sent to three different S&Hs, one for
each channel, and made available to the outside.
The low noise input amplifier operates at 200 kHz while the three S&Hs operate at a sampling frequency of 66
kHz. This allows a large oversampling ratio, which leads to in-band noise reduction and to an accurate output
waveform.
All the analog parameters (output offset voltage and sensitivity) are ratiometric to the voltage supply. Increasing
or decreasing the voltage supply, the sensitivity and the offset will increase or decrease linearly. The feature
provides the cancellation of the error related to the voltage supply along an analog to digital conversion chain.
3.3 Factory calibration
The IC interface is factory calibrated to provide to the final user a device ready to operate.
The trimming values are stored inside the device by a non volatile structure. Any time the device is turned on,
the trimming parameters are downloaded into the registers to be employed during the normal operation thus
allowing the final user to employ the device without any need for further calibration.
相關PDF資料 |
PDF描述 |
|---|---|
| LIS3L02DQ-TR | SPECIALTY ANALOG CIRCUIT, QCC44 |
| LIS3L02DQ | SPECIALTY ANALOG CIRCUIT, QCC44 |
| LIT1108CS8-5#PBF | 1.5 A SWITCHING REGULATOR, 25 kHz SWITCHING FREQ-MAX, PDSO8 |
| LIT1108CS8-12#PBF | 1.5 A SWITCHING REGULATOR, 25 kHz SWITCHING FREQ-MAX, PDSO8 |
| LK1001-7EDDT | 1-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS3L02AQ3 | 功能描述:加速計 - 板上安裝 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3L02AQ3TR | 功能描述:加速計 - 板上安裝 INERTIAL SNSR 3 Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3L02AQ5 | 功能描述:加速計 - 板上安裝 Dual low power opamp RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3L02AQ5TR | 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3L02AQ-TR | 功能描述:ACCELEROMETER TRPL AXIS 44QFN RoHS:是 類別:傳感器，轉換器 >> 加速計 系列:- 標準包裝:1 系列:SCA1000 軸:X，Y 加速范圍:±1.7g 靈敏度:1.2V/g 電源電壓:4.75 V ~ 5.25 V 輸出類型:數字 帶寬:50±30Hz 接口:SPI 安裝類型:表面貼裝 封裝/外殼:12-SMD 供應商設備封裝:12-SMD 其它名稱:551-1007-1 |
發布緊急采購，3分鐘左右您將得到回復。