- 您現在的位置：買賣IC網 > PDF目錄44034 > LK4301-7ERD0B2 (POWER-ONE INC) 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE PDF資料下載
參數資料
| 型號： | LK4301-7ERD0B2 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| 封裝： | HEAT SINK, METAL, CASE K02 |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 1215K |
| 代理商： | LK4301-7ERD0B2 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
K Series
AC-DC Converters >100 Watt
Rugged Environment
Edition 4/4.99
12/28
MELCHER
The Power Partners.
0
t
0
Inhibit
1
0.1
1
Uo/Uo nom
tr
tf
06001
Sense Lines
(Only for single output units 5.1 V, 12 V, 15 V, 24 V)
This feature enables for compensation of voltage drops
across the connector contacts and if necessary, across the
load lines. If the sense lines are connected at the load
rather than directly at the connector, the user should ensure
that
Uo max (between Vo1+ and Vo1–) is not exceeded. We
recommend connecting the sense lines directly at the fe-
male connector.
For further information, please refer to:
Application Notes.
To ensure correct operation, both sense lines (S+ and S–)
should be connected to their respective power outputs
(Vo1+ and Vo1–) and the voltage difference between any
sense line and its respective power output pin (as meas-
ured on the connector) should not exceed the following val-
ues:
Table 6: Maximum Voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
<0.5 V
<0.25 V
12 V, 15 V
<1.0 V
<0.25 V
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Uinh Inhibit
Uo = on
Ui min…Ui max
–50
0.8
V
voltage
Uo = off
2.4
50
Iinh
Inhibit current
Uinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
If the output voltages are increased above
Uo nom via R-in-
put control, option P setting, remote sensing or option T, the
output currents must be reduced accordingly so that
Po nom is not exceeded.
Important: The output terminals Vo1+ and Vo1– must
always be connected to the load before connecting the
sense lines S+ and S–, otherwise the unit will be dam-
aged.
Fig. 19
Output response as a function of inhibit control
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input: Output is disabled (
Uo = off).
The outputs of the module may be enabled or disabled by
means of a logic signal (TTL, CMOS, etc.) applied between
the inhibit input i and the negative pin of output 1 (Vo1–). In
systems with several units, this feature can be used, for ex-
ample, to control the activation sequence of the converters.
If the inhibit function is not required, connect the inhibit pin
18 to pin 14 to enable the outputs (active low logic, fail safe).
For output response refer to:
Hold-up Time and Output Re-
sponse.
Vi+
Vi–
Vo–
i
Vo+
Iinh
Uinh
06031
1.6
0.8
0
–0.8
–50
Uinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Uinh = 0.8 V
Uo = on
Uo = off
Uinh = 2.4 V
06032
Fig. 17
Definition of Uinh and Iinh.
Fig. 18
Typical inhibit current Iinh versus inhibit voltage Uinh
相關PDF資料 |
PDF描述 |
|---|---|
| LK4301-7ERD5T | 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK4301-7PD3T | 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK4301-7RD3B2 | 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK4301-7RD3T | 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK4301-9RD6B1 | 1-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LK4301-7R | 功能描述:線性和開關式電源 Euro-Cassette 144W (12V) RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| LK4301-9ER | 制造商:Power-One 功能描述:AC/DC PS SGL-OUT 12V 12A 280W 15PIN - Bulk |
| LK4303-9ERD4T | 制造商:Power-One 功能描述:- Bulk |
| LK4402 | 制造商:CLINCH NUT 功能描述: |
| LK-440-2 | 制造商:PennEngineering (PEM) 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。