- 您現在的位置：買賣IC網 > PDF目錄44049 > LK5660-7ERD6T (POWER-ONE INC) 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE PDF資料下載
參數資料
| 型號： | LK5660-7ERD6T |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| 封裝： | HEAT SINK, METAL, CASE K02, MODULE |
| 文件頁數： | 13/28頁 |
| 文件大?。?/td> | 1215K |
| 代理商： | LK5660-7ERD6T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
K Series
AC-DC Converters >100 Watt
Rugged Environment
Edition 4/4.99
20/28
MELCHER
The Power Partners.
Table 13: Isolation
Characteristic
Input to
Output to Output to
Unit
case
output
case
output
Electric
Required according to
1.5
3.0 1
––
kVrms
strength
IEC/EN 60950
2.1
4.2 1
––
kV DC
test voltage
Actual factory test 1 s
2.8
5.6 1
1.4
0.14
AC test voltage equivalent
2.0
4.0 1
1.0
0.1
kVrms
to actual factory test
Insulation resistance at 500 V DC
>300
>100 2
M
1 In accordance with IEC/EN 60950 only subassemblies are tested in factory with this voltage.
2 Tested at 100 V DC.
For creepage distances and clearances refer to:
Technical Information: Safety.
Due to high current values, all LK units provide two inter-
nally parallel connected contacts for certain paths (pins 4/6,
8/10, 26/28 and 30/32, respectively). It is recommended to
connect load and supply to both female connector pins of
each path in order to keep the voltage drop across the con-
nector pins to an absolute minimum and to not over-
stress the connector contacts if currents are higher than
approx. 8 A. The connector contacts are rated 8 A over the
whole temperature range.
Make sure that there is sufficient air flow available for con-
vection cooling. This should be verified by measuring the
case temperature when the unit is installed and operated in
the end-use application. The maximum specified case tem-
perature
TC max shall not be exceeded. See also: Thermal
Considerations.
Check for hazardous voltages before altering any connec-
tions.
Ensure that a unit failure (e.g. by an internal short-circuit)
does not result in a hazardous condition. See also:
Safety
of operator accessible output circuit.
Cleaning Agents
In order to avoid possible damage, any penetration of
cleaning fluids is to be prevented, since the power supplies
are not hermetically sealed.
Protection Degree
Condition: Female connector fitted to the unit.
IP 30: All units except those with option P, and except
those with option D or V with potentiometer.
IP 20: All units fitted with option P, or with option D or V
with potentiometer.
Standards and Approvals
All AC-DC converters correspond to class I equipment.
They are UL recognized according to UL 1950, UL recog-
nized for Canada to CAN/CSA C22.2 No. 950-95 and LGA
approved to IEC/EN 60950 standards.
The units have been evaluated for:
Building in
Basic insulation between input and case, based on 250 V
AC and 400 V DC
Double or reinforced insulation between input and output,
based on 250 V AC and 400 V DC
Basic insulation between output and case based on
200 V AC and DC.
Operational insulation between output and output
The use in a pollution degree 2 environment
Connecting the input to a primary or secondary circuit
which is subject to a maximum transient rating of 2500 V
(overvoltage category III based on a 110 V primary cir-
cuit, overvoltage category II based on a 230 V primary
circuit).
The UL 1950 recognition limits the maximum case tem-
perature of the standard modules to
TC = TC max – 10 K =
95
°C.
The AC-DC converters are subject to manufacturing sur-
veillance in accordance with the above mentioned UL,
CSA, EN and with ISO 9001 standards.
Isolation
The electric strength test is performed as factory test in ac-
cordance with IEC/EN 60950 and UL 1950 and should not
be repeated in the field. Melcher will not honour any guar-
antee claims resulting from electric strength field tests.
Important: Testing by applying AC voltages will result in
high and dangerous leakage currents flowing through
the Y-capacitors (see fig.:
Block diagram).
相關PDF資料 |
PDF描述 |
|---|---|
| LK5660-7PD9 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-7RD9B2 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-9PB2 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-9PD7TB1 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
| LK5660-9PDDTB2 | 2-OUTPUT 150 W AC-DC PWR FACTOR CORR MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LK5660-7R | 功能描述:線性和開關式電源 24V/3A OUT AC-DC CONVERTER RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫(yī)用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| LK5660-9ER | 制造商:Power-One 功能描述:AC/DC PS DUAL-OUT 24V/24V 5.2A/5.2A 280W 15PIN - Bulk |
| LK-590-001 | 功能描述:LED MODULE 1W AMBER RoHS:是 類別:光電元件 >> LED - 高亮度電源模塊 系列:- 標準包裝:36 系列:5027 TFFC STAR K2 顏色:暖白色 配置:星形 在特定電流下的光通量 - 測試:75lm 電流 - 測試:350mA 電流 - 最大:1.5A 帶連接器:無 驅動器電路:無 波長:- 電壓:- |
| LK-590-001-FC | 功能描述:LED MODULE 1W AMBER W/CONN RoHS:是 類別:光電元件 >> LED - 高亮度電源模塊 系列:- 標準包裝:36 系列:5027 TFFC STAR K2 顏色:暖白色 配置:星形 在特定電流下的光通量 - 測試:75lm 電流 - 測試:350mA 電流 - 最大:1.5A 帶連接器:無 驅動器電路:無 波長:- 電壓:- |
| LK-59A-1 | 制造商:ITT Interconnect Solutions 功能描述:OBS - Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。