- 您現在的位置：買賣IC網 > PDF目錄69004 > LM10010SDX (NATIONAL SEMICONDUCTOR CORP) SWITCHING REGULATOR, PDSO10 PDF資料下載
參數資料
| 型號： | LM10010SDX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, PDSO10 |
| 封裝： | 3 X 3 MM, 0.50 MM PITCH, LLP-10 |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 308K |
| 代理商： | LM10010SDX |
Using 1% resistor values, R
FB1 can be set to 6.81 k and
R
FB2 can be set to 8.06 k. This will yield a regulator output
range of 0.704V to 1.107V. At startup, the code of the
LM10010 will be 46d (101110b) and will output a 15.97 A.
This will give an output voltage of approximately 1.0V
(0.998V) when power is applied and both the LM10010 and
the LM21215A-1 come out of UVLO. Of course, values cal-
culated here will be dependent on the accuracy of the regu-
lator, the LM10010 IDAC, and the resistor values used in the
circuit.
Table 1 shows the codes and some of the resultant values of
the IDAC current and the corresponding regulator output volt-
age for the previous example.
TABLE 1. VID Codes with IDAC Current and Regulator
Voltage for the Example in Figure 4.
VID Code
IDAC Current
(A)
Regulator
Voltage (V)
000000b
59.20
0.7038
000001b
58.26
0.7102
000010b
57.32
0.7166
000011b
56.38
0.7230
...
111100b
2.82
1.0878
111101b
1.88
1.0941
111110b
0.94
1.1005
111111b
0.00
1.1069
PC BOARD GUIDELINES
The following guidelines should be followed when designing
the PC board for the LM10010:
- Place the LM10010 close to the regulator feedback pin to
minimize the FB trace length.
- Place a small capacitor, C
VDD, (1 nF) directly adjacent to the
VDD and GND pins of the LM10010 to help minimize tran-
sients which may occur on the input supply line.
- The high current path from the board’s input to the load and
the return path should be parallel and close to each other to
minimize loop inductance.
- The ground connections for the various components around
the LM10010 should be connected directly to each other, and
to the LM10010’s GND pins, and then connected to the sys-
tem ground at one point. Do not connect the various compo-
nent grounds to each other through the high current ground
line.
- For additional information about the operation of the regu-
lator, please consult the respective datasheet and application
notes on the repective evaluation boards.
www.national.com
10
LM10010
相關PDF資料 |
PDF描述 |
|---|---|
| LM12L458CIVX | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LM185BYH-MLS | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, MBCY3 |
| LM234H/NOPB | SPECIALTY ANALOG CIRCUIT, MBCY3 |
| LM25085MMY | SWITCHING CONTROLLER, PDSO8 |
| LM25119PSQX | DUAL SWITCHING CONTROLLER, QCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM10010SDX/NOPB | 功能描述:其他電源管理 RoHS:否 制造商:Texas Instruments 輸出電壓范圍: 輸出電流:4 mA 輸入電壓范圍:3 V to 3.6 V 輸入電流: 功率耗散: 工作溫度范圍:- 40 C to + 110 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-48 封裝:Reel |
| LM10011 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:6/4-Bit VID Programmable Current DAC for Point of Load Regulators with Adjustable Start-Up Current |
| LM10011EVM | 制造商:Texas Instruments 功能描述:LM10011EVM - Boxed Product (Development Kits) 制造商:Texas Instruments 功能描述:EVALUATION MODULE LM10011 |
| LM10011SD/NOPB | 功能描述:數模轉換器- DAC 4/6B VID VTG Programmer RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| LM10011SDNOPB | 制造商:National Semiconductor 功能描述:LM10011SDNOPB |
發布緊急采購，3分鐘左右您將得到回復。