- 您現在的位置：買賣IC網 > PDF目錄358804 > LM1084IT-ADJ (NATIONAL SEMICONDUCTOR CORP) 5A Low Dropout Positive Regulators PDF資料下載
參數資料
| 型號： | LM1084IT-ADJ |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 5A Low Dropout Positive Regulators |
| 中文描述： | 1.2 V-15 V ADJUSTABLE POSITIVE LDO REGULATOR, 1.5 V DROPOUT, PSFM3 |
| 封裝： | TO-220, 3 PIN |
| 文件頁數： | 7/13頁 |
| 文件大小： | 750K |
| 代理商： | LM1084IT-ADJ |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁
Application Note
GENERAL
Figure 1
shows a basic functional diagram for the LM1084-
Adj (excluding protection circuitry) . The topology is basically
that of the LM317 except for the pass transistor. Instead of a
Darlingtion NPN with its two diode voltage drop, the LM1084
uses a single NPN. This results in a lower dropout voltage.
The structure of the pass transistor is also known as a quasi
LDO. The advantage a quasi LDO over a PNP LDO is its
inherently lower quiescent current. The LM1084 is guaran-
teed to provide a minimum dropout voltage 1.5V over tem-
perature, at full load.
OUTPUT VOLTAGE
The LM1084 adjustable version develops at 1.25V reference
voltage, (V
), between the output and the adjust terminal.
As shown in figure 2, this voltage is applied across resistor
R1 to generate a constant current I1. This constant current
then flows through R2. The resulting voltage drop across R2
adds to the reference voltage to sets the desired output
voltage.
The current I
ADJ
from the adjustment terminal introduces an
output error . But since it is small (120uA max), it becomes
negligible when R1 is in the 100
range.
For fixed voltage devices, R1 and R2 are integrated inside
the devices.
STABILITY CONSIDERATION
Stability consideration primarily concern the phase response
of the feedback loop. In order for stable operation, the loop
must maintain negative feedback. The LM1084 requires a
certain amount series resistance with capacitive loads. This
series resistance introduces a zero within the loop to in-
crease phase margin and thus increase stability. The equiva-
lent series resistance (ESR) of solid tantalum or aluminum
electrolytic capacitors is used to provide the appropriate zero
(approximately 500 kHz).
The Aluminum electrolytic are less expensive than tantal-
ums, but their ESR varies exponentially at cold tempera-
tures; therefore requiring close examination when choosing
the desired transient response over temperature. Tantalums
are a convenient choice because their ESR varies less than
2:1 over temperature.
The recommended load/decoupling capacitance is a 10uF
tantalum or a 50uF aluminum. These values will assure
stability for the majority of applications.
The adjustable versions allows an additional capacitor to be
used at theADJ pin to increase ripple rejection. If this is done
the output capacitor should be increased to 22uF for tantal-
ums or to 150uF for aluminum.
Capacitors other than tantalum or aluminum can be used at
the adjust pin and the input pin. A 10uF capacitor is a
reasonable value at the input. See Ripple Rejection section
regarding the value for the adjust pin capacitor.
It is desirable to have large output capacitance for applica-
tions that entail large changes in load current (microproces-
sors for example). The higher the capacitance, the larger the
available charge per demand. It is also desirable to provide
low ESR to reduce the change in output voltage:
V =
I x ESR
It is common practice to use several tantalum and ceramic
capacitors in parallel to reduce this change in the output
voltage by reducing the overall ESR.
Output capacitance can be increased indefinitely to improve
transient response and stability.
RIPPLE REJECTION
Ripple rejection is a function of the open loop gain within the
feed-back loop (refer to
Figure 1
and
Figure 2
). The LM1084
exhibits 75dB of ripple rejection (typ.). When adjusted for
voltages higher than V
, the ripple rejection decreases as
function of adjustment gain: (1+R1/R2) or V
/V
. There-
fore a 5V adjustment decreases ripple rejection by a factor of
four (12dB); Output ripple increases as adjustment voltage
increases.
However, the adjustable version allows this degradation of
ripple rejection to be compensated. The adjust terminal can
be bypassed to ground with a capacitor (C
). The imped-
ance of the C
should be equal to or less than R1 at the
desired ripple frequency. This bypass capacitor prevents
ripple from being amplified as the output voltage is in-
creased.
1/(2
π
*f
RIPPLE
*C
ADJ
)
≤
R
1
LOAD REGULATION
The LM1084 regulates the voltage that appears between its
output and ground pins, or between its output and adjust
pins. In some cases, line resistances can introduce errors to
the voltage across the load. To obtain the best load regula-
tion, a few precautions are needed.
10094665
FIGURE 1. Basic Functional Diagram for the LM1084,
excluding Protection circuitry
10094617
FIGURE 2. Basic Adjustable Regulator
L
www.national.com
7
相關PDF資料 |
PDF描述 |
|---|---|
| LM1084ISX-12 | 5A Low Dropout Positive Regulators |
| LM1084ISX-3.3 | 5A Low Dropout Positive Regulators |
| LM1084ISX-ADJ | 5A Low Dropout Positive Regulators |
| LM1084IS-ADJ | 5A Low Dropout Positive Regulators |
| LM1084IS-5.0 | 5A Low Dropout Positive Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1084IT-ADJ/NOPB | 功能描述:低壓差穩壓器 - LDO 5A LDO POS REG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM1084IT-ADJ/NOPB | 制造商:Texas Instruments 功能描述:Linear Voltage Regulator IC |
| LM1084M | 制造商:SEME-LAB 制造商全稱:Seme LAB 功能描述:5 AMP POSITIVE |
| LM1084R | 制造商:HTC 制造商全稱:HTC Korea TAEJIN Technology Co. 功能描述:5A L.D.O. VOLTAGE REGULATOR (Adjustable & Fixed) |
| LM1084RS | 制造商:HTC 制造商全稱:HTC Korea TAEJIN Technology Co. 功能描述:5A L.D.O. VOLTAGE REGULATOR (Adjustable & Fixed) |
發布緊急采購，3分鐘左右您將得到回復。