- 您現在的位置：買賣IC網 > PDF目錄358804 > LM1085IT-12 (NATIONAL SEMICONDUCTOR CORP) 3A Low Dropout Positive Regulators PDF資料下載
參數資料
| 型號： | LM1085IT-12 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 3A Low Dropout Positive Regulators |
| 中文描述： | 12 V FIXED POSITIVE LDO REGULATOR, 1.5 V DROPOUT, PSFM3 |
| 封裝： | TO-220, 3 PIN |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 744K |
| 代理商： | LM1085IT-12 |
Application Note
(Continued)
Figure 3
shows a typical application using a fixed output
regulator. Rt1 and Rt2 are the line resistances. V
LOAD
is less
than the V
OUT
by the sum of the voltage drops along the line
resistances. In this case, the load regulation seen at the
R
LOAD
would be degraded from the data sheet specification.
To improve this, the load should be tied directly to the output
terminal on the positive side and directly tied to the ground
terminal on the negative side.
When the adjustable regulator is used (
Figure 4
), the best
performance is obtained with the positive side of the resistor
R1 tied directly to the output terminal of the regulator rather
than near the load. This eliminates line drops from appearing
effectively in series with the reference and degrading regu-
lation. For example, a 5V regulator with 0.05
resistance
between the regulator and load will have a load regulation
due to line resistance of 0.05
x I
L
. If R1 (= 125
) is
connected near the load the effective line resistance will be
0.05
(1 + R2/R1) or in this case, it is 4 times worse. In
addition, the ground side of the resistor R2 can be returned
near the ground of the load to provide remote ground sens-
ing and improve load regulation.
PROTECTION DIODES
Under normal operation, the LM1085 regulator does not
need any protection diode. With the adjustable device, the
internal resistance between the adjustment and output ter-
minals limits the current. No diode is needed to divert the
current around the regulator even with a capacitor on the
adjustment terminal. The adjust pin can take a transient
signal of
±
25V with respect to the output voltage without
damaging the device.
When an output capacitor is connected to a regulator and
the input is shorted, the output capacitor will discharge into
the output of the regulator. The discharge current depends
on the value of the capacitor, the output voltage of the
regulator, and rate of decrease of V
IN
. In the LM1085 regu-
lator, the internal diode between the output and input pins
can withstand microsecond surge currents of 10A to 20A.
With an extremely large output capacitor (
≥
1000 μf), and
with input instantaneously shorted to ground, the regulator
could be damaged. In this case, an external diode is recom-
mended between the output and input pins to protect the
regulator, shown in
Figure 5
.
OVERLOAD RECOVERY
Overload recovery refers to regulator’s ability to recover from
a short circuited output. A key factor in the recovery process
is the current limiting used to protect the output from drawing
too much power. The current limiting circuit reduces the
output current as the input to output differential increases.
Refer to short circuit curve in the curve section.
During normal start-up, the input to output differential is
small since the output follows the input. But, if the output is
shorted, then the recovery involves a large input to output
differential. Sometimes during this condition the current lim-
iting circuit is slow in recovering. If the limited current is too
low to develop a voltage at the output, the voltage will
stabilize at a lower level. Under these conditions it may be
necessary to recycle the power of the regulator in order to
get the smaller differential voltage and thus adequate start
up conditions. Refer to curve section for the short circuit
current vs. input differential voltage.
THERMAL CONSIDERATIONS
ICs heats up when in operation, and power consumption is
one factor in how hot it gets. The other factor is how well the
heat is dissipated. Heat dissipation is predictable by knowing
the thermal resistance between the IC and ambient (
θ
JA
).
Thermal resistance has units of temperature per power (C/
W). The higher the thermal resistance, the hotter the IC.
The LM1085 specifies the thermal resistance for each pack-
age as junction to case (
θ
). In order to get the total
resistance to ambient (
θ
JA
), two other thermal resistance
10094718
FIGURE 3. Typical Application using Fixed Output
Regulator
10094719
FIGURE 4. Best Load Regulation using Adjustable
Output Regulator
10094715
FIGURE 5. Regulator with Protection Diode
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM1085IT-3.3 | 3A Low Dropout Positive Regulators |
| LM1085IT-5.0 | 3A Low Dropout Positive Regulators |
| LM1085IT-ADJ | 3A Low Dropout Positive Regulators |
| LM1085 | 3A Low Dropout Positive Regulators |
| LM1085S-1.5 | 3A LOW DROPOUT VOLTAGE REGULATOR (Adjustable & Fixed) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1085IT-12/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM1085IT-3.3 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM1085IT-3.3/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM1085IT-3.3/NOPB | 制造商:Texas Instruments 功能描述:Linear Voltage Regulator IC |
| LM1085IT-5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:3A Low Dropout Positive Regulators(313.07 k) |
發布緊急采購，3分鐘左右您將得到回復。