- 您現在的位置：買賣IC網 > PDF目錄358805 > LM1117I PDF資料下載
參數資料
| 型號： | LM1117I |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 274K |
| 代理商： | LM1117I |
LM111, LM211, LM311, LM311Y
DIFFERENTIAL COMPARATORS WITH STROBES
SLCS007A – SEPTEMBER 1973 – REVISED FEBRUARY 1992
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics at V
CC
±
=
±
15 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
LM311Y
TYP
UNIT
MIN
MAX
7.5
VIO
IIO
IIB
IIL(S)
Input offset voltage
See Note 5
2
mV
Input offset current
See Note 5
6
50
nA
Input bias current
VO = 1 V to 14 V
V(strobe) = 0.3 V,
100
250
nA
Low-level strobe current (see Note 6)
VID
≤
–10 mV
–3
mA
VICR
Common-mode input voltage range
13
to
–14.5
13.8
to
–14.7
V
AVD
IOH
Large-signal differential voltage amplification
VO = 5 V to 35 V,
Istrobe = –3 mA,
RL = 1 k
VID = 5 mV,
40
200
V/mV
High-level (collector) output current
VOH = 35 V
0.2
50
nA
VOL
Low-level (collector-to-emitter) output
voltage
IOL = 50 mA,
VID = –10 mV
0.75
1.5
V
ICC+
ICC–
Unless otherwise noted, all characteristics are measured with BALANCE and BAL/STRB open and the emitter output grounded.
NOTES:
5. The offset voltages and offset currents given are the maximum values required to drive the collector output up to 14 V or down to
1 V with a pullup resistor of 7.5 k
to VCC+. These parameters actually define an error band and take into account the worst-case
effects of voltage gain and input impedance.
6. The strobe should not be shorted to ground; it should be current driven at –3 mA to –5 mA (see Figures 13 and 27).
Supply current from VCC+, output low
Supply current from VCC–, output low
VID = –10 mV,
VID = 10 mV,
No load
5.1
7.5
mA
No load
–4.1
–5
mA
switching characteristics, V
CC
±
=
±
15 V, T
A
= 25
°
C
PARAMETER
TEST CONDITIONS
LM311Y
TYP
115
UNIT
MIN
MAX
Response time, low-to-high-level output
Response time, high-to-low-level output
RC= 500
RC = 500
to 5 V,
CL= 5 pF
CL = 5 pF,
See Note 7
ns
165
ns
NOTE 7: The response time specified is for a 100-mV input step with 5-mV overdrive and is the interval between the input step function and the
instant when the output crosses 1.4 V.
相關PDF資料 |
PDF描述 |
|---|---|
| LM111 | Voltage comparator |
| LM111 | VOLTAGE COMPARATORS |
| LM111N | VOLTAGE COMPARATORS |
| LM111D | VOLTAGE COMPARATORS |
| LM111FE | INTELLIGENT DISP 8CHAR 5X7 HER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1117IDT-3.3 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM1117IDT-3.3/NOPB | 功能描述:低壓差穩壓器 - LDO 800MA LDO LINEAR REG RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM1117IDT-3.3/NOPB | 制造商:Texas Instruments 功能描述:Voltage Regulator IC |
| LM1117IDT-33 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM1117-N/LM1117I 800mA Low-Dropout Linear Regulator |
| LM1117IDT-5.0 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。