- 您現在的位置：買賣IC網 > PDF目錄367561 > LM1279AN Triple Video Amplifier PDF資料下載
參數資料
| 型號： | LM1279AN |
| 元件分類： | 視頻放大器 |
| 英文描述： | Triple Video Amplifier |
| 中文描述： | 三路視頻放大器 |
| 文件頁數： | 3/13頁 |
| 文件大小： | 511K |
| 代理商： | LM1279AN |
AC Electical Characteristics
(Continued)
T
= 25C; V
= V
CC2
= 8V. Manually adjust Video Output pins 13, 15, and 18 to 4V DC for the AC test unless otherwise
stated. (Note 15)
Symbol
Parameter
Conditions
Typical
(Note 5)
50
Limit
(Note 6)
Units
V
sep
10 MHz
V
OL
(OSD)
Video Amplifier 10 MHz Isolation
OSD Black Level, Difference from
Video Black Level
OSD Output High Voltage (above
measured video black level)
Going into OSD Mode
Going out of OSD Mode
Starting OSD Propagation Delay
Ending OSD Propagation Delay
Input Clamp Pulse Width
V
10
= 4V (Notes 11, 13)
V
OSD in
= 0.8V, OSD Mode
dB
0.4
0.7
V (max)
V
OH
(OSD)
V
OSD in
= 2.5V, OSD Mode
2.1
2.4
V (max)
t
r
(OSD)
t
f
(OSD)
t
r-prop
(OSD)
t
f-prop
(OSD)
T
pw
(Clamp)
OSD Mode (Figure 2)
OSD Mode (Figure 2)
Switching to OSD Mode (Figure 3)
Switching to Vid. Mode (Figure 3)
(Note 14)
5.0
10.0
13.0
14.0
ns
ns
ns
ns
200
ns (min)
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Note 2:
Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and
test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may de-
grade when the device is not operated under the listed test conditions.
Note 3:
V
CC
supply pins 2 and 16 must be externally wired together to prevent internal damage during V
CC
power on/off cycles.
Note 4:
Human body model, 100 pF discharged through a 1.5 k
resistor.
Note 5:
Typical specifications are specified at +25C and represent the most likely parametric norm.
Note 6:
Tested limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 7:
The supply current specified is the current for V
and V
minus the current through R
L
(I
= I
+ I
CC2
I
L
). The supply current for V
CC2
(pin 16)
does depend on the output load. With video output at 1V DC, the additional current through V
CC2
is 7.7 mA with R
L
.
Note 8:
Output voltage is dependent on load resistor. Test circuit uses R
L
= 390
.
Note 9:
Measure gain difference between any two amplifiers. V
IN
= 635 mV
PP
.
Note 10:
A
V
track is a measure of the ability of any two amplifiers to track each other and quantifies the matching of the three attenuators. It is the difference in
gain change between any two amplifiers with the contrast voltage (V
) at either 4V or 2V measured relative to an A
max condition, V
10
= 4V. For example, at A
V
max the three amplifiers’ gains might be 17.1 dB, 16.9 dB, and 16.8 dB and change to 11.2 dB, 10.9 dB and 10.7 dB respectively for V
10
= 2V. This yields the mea-
sured typical
±
0.1 dB channel tracking.
Note 11:
When measuring video amplifier bandwidth or pulse rise and fall times, a double sided full ground plane printed circuit board without socked is recom-
mended. Video amplifier 10 MHz isolation test also requires this printed circuit board. The reason for a double sided full ground plane PCB is that large measurement
variations occur in single sided PCBs.
Note 12:
Adjust input frequency from 10 MHz (A
V
max reference level) to the 3 dB corner frequency (f
3 dB
).
Note 13:
Measure output levels of the other two undriven amplifiers relative to the driven amplifier to determine channel separation. Terminate the undriven amplifier
inputs to simulate generator loading. Repeat test at f
IN
= 10 MHz for V
sep
10 MHz.
Note 14:
A minimum pulse width of 200 ns is guaranteed for a horizontal line of 15 kHz. This limit is guaranteed by design. If a lower line rate is used then a longer
clamp pulse may be required.
Note 15:
During the AC test the 4V DC level is the center voltage of the AC output signal. For example, if the output is 4 V
PP
the signal will swing between 2V DC
and 6V DC.
Note 16:
Machine Model ESD test is covered by specification EIAJ IC-121-1981. A 200 pF cap is charged to the specified voltage, then discharged directly into the
IC with no external series resistor (resistance of discharge path must be under 50
).
L
www.national.com
3
相關PDF資料 |
PDF描述 |
|---|---|
| LM12CK | Voltage-Feedback Operational Amplifier |
| LM13121 | |
| LM131 | Precision Voltage-to-Frequency Converters |
| LM131A | Precision Voltage-to-Frequency Converters |
| LM134H-6 | Current Source |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1279DL WAF | 制造商:Texas Instruments 功能描述: |
| LM1279N | 功能描述:IC VIDEO AMP SYS 110MHZ 20-DIP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| LM1281 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:85 MHz RGB Video Amplifier System with On Screen Display (OSD) |
| LM1281CL WAF | 制造商:Texas Instruments 功能描述: |
| LM1281N | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Panasonic Industrial Company 功能描述:IC |
發布緊急采購，3分鐘左右您將得到回復。