- 您現在的位置：買賣IC網 > PDF目錄358812 > LM1575J-ADJ-QML (NATIONAL SEMICONDUCTOR CORP) Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:15; Connector Shell Size:15; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No PDF資料下載
參數資料
| 型號： | LM1575J-ADJ-QML |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Circular Connector; MIL SPEC:MIL-DTL-38999 Series I; Body Material:Metal; Series:LJT; No. of Contacts:15; Connector Shell Size:15; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No |
| 中文描述： | 3 A SWITCHING REGULATOR, 58 kHz SWITCHING FREQ-MAX, CDIP16 |
| 封裝： | CERDIP-16 |
| 文件頁數： | 15/27頁 |
| 文件大?。?/td> | 725K |
| 代理商： | LM1575J-ADJ-QML |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Inductor Value Selection Guides
(For Continuous Mode Operation) (Continued)
PROCEDURE (Adjustable Output Voltage Versions)
Given:
V
OUT
= Regulated Output Voltage V
IN
(Max) =
Maximum Input Voltage I
LOAD
(Max) = Maximum Load
Current F = Switching Frequency
(Fixed at 52 kHz)
1. Programming Output Voltage
(Selecting R1 and R2, as
shown in Figure 2
) Use the following formula to select the
appropriate resistor values.
EXAMPLE (Adjustable Output Voltage Versions)
Given:
V
OUT
= 10V V
IN
(Max) = 25V I
LOAD
(Max) = 1A F =
52 kHz
R
can be between 1k and 5k.
(For best temperature coef-
ficient and stability with time, use 1% metal film resistors)
1.Programming Output Voltage
(Selecting R1 and R2)
R2 = 1k (8.13 1) = 7.13k, closest 1% value is 7.15k
2. Inductor Selection (L1) A.
Calculate the inductor Volt
microsecond constant, E
T (V
μs), from the following
formula:
B.
Use the E
T value from the previous formula and match
it with the E
T number on the vertical axis of the
Inductor
Value Selection Guide
shown in
Figure 7
.
C.
On the hori-
zontal axis, select the maximum load current.
D.
Identify the
inductance region intersected by the E
T value and the
maximum load current value, and note the inductor code for
that region.
E.
Identify the inductor value from the inductor
code, and select an appropriate inductor from the table shown
in
Figure 9
. Part numbers are listed for three inductor manu-
facturers. The inductor chosen must be rated for operation at
the LM2575 switching frequency (52 kHz) and for a current
rating of 1.15 x I
. For additional inductor information, see
the inductor section in the application hints section of this data
sheet.
3. Output Capacitor Selection (C
OUT
) A.
The value of the
output capacitor together with the inductor defines the
dominate pole-pair of the switching regulator loop. For
stable operation, the capacitor must satisfy the following
requirement:
2. Inductor Selection (L1) A.
Calculate E
T (V
μs)
B.
E
T = 115 V
μs
C.
I
(Max) = 1A
D.
Inductance
Region = H470
E.
Inductor Value = 470 μH
Choose from
AIE
part #430-0634,
Pulse Engineering
part #PE-53118, or
Renco
part #RL-1961.
The above formula yields capacitor values between 10 μF
and 2000 μF that will satisfy the loop requirements for stable
operation. But to achieve an acceptable output ripple voltage,
(approximately 1% of the output voltage) and transient re-
sponse, the output capacitor may need to be several times
larger than the above formula yields.
B.
The capacitor’s volt-
age rating should be at last 1.5 times greater than the output
voltage. For a 10V regulator, a rating of at least 15V or more
is recommended. Higher voltage electrolytic capacitors gen-
erally have lower ESR numbers, and for this reason it may be
necessary to select a capacitor rate for a higher voltage than
would normally be needed.
4. Catch Diode Selection (D1) A.
The catch-diode current
rating must be at least 1.2 times greater than the maximum
load current. Also, if the power supply design must
withstand a continuous output short, the diode should have
a current rating equal to the maximum current limit of the
LM2575. The most stressful condition for this diode is an
overload or shorted output. See diode selection guide in
Figure 8
.
B.
The reverse voltage rating of the diode should
be at least 1.25 times the maximum input voltage.
3. Output Capacitor Selection (C
OUT
) A.
However, for acceptable output ripple voltage select C
OUT
≥
220 μF C
OUT
= 220 μF electrolytic capacitor
4. Catch Diode Selection (D1) A.
For this example, a 3A
current rating is adequate.
B.
Use a 40V MBR340 or
31DQ04 Schottky diode, or any of the suggested
fast-recovery diodes in
Figure 8
.
L
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM1575J-15-QML | SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
| LM1575J-3.3-QML | SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
| LM1575J-5.0-QML | SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
| LM1575J-12-QML | SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
| LM1575 | SIMPLE SWITCHER 1A Step-Down Voltage Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM1575K-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| LM1575K-12/883 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| LM1575K-12/883C | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LM1575K-12/883QF | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LM1575K-12-QML | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:SIMPLE SWITCHER 1A STEP-DOWN VOLTAGE REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。