- 您現在的位置：買賣IC網 > PDF目錄367561 > LM1897N Single Audio Preamp PDF資料下載
參數資料
| 型號： | LM1897N |
| 英文描述： | Single Audio Preamp |
| 中文描述： | 單音頻前置放大器 |
| 文件頁數： | 5/10頁 |
| 文件大?。?/td> | 291K |
| 代理商： | LM1897N |
External Component Guide
(Figure 1)
Component
Value
C1
0.1 μF–
100 μF
Purpose
May be part of power supply,
or may be added to suppress
power supply oscillation.
Blocks DC, pin 2 and pin 13
are at DC potential of V
S
/2.
C2, C13 form a low frequency
pole with 20k R
IN
.
C2, C13
1 μF
C14
25 μF–
100 μF
0.0033 μF
Improves power supply
rejection.
Forms integrator with internal
gm block and op amp. Sets
bandwidth conversion gain of
33 Hz/μA of gm current.
Output coupling capacitor.
Output is at DC potential of
V
S
/2.
Works with R1 and R2 to
attenuate low frequency
transients which could disturb
control path operation.
C3, C12
C4, C11
1 μF
C5
0.1 μF
C6
0.001 μF
Works with input resistance of
pin 6 to form part of control
path frequency weighting.
C8
0.1 μF
Combined with L8 and C
L
forms 19 kHz filter for FM
pilot. This is only required in
FM applications (Note 9).
Forms 19 kHz filter for FM
pilot. L8 is Toko coil
CAN-1A185HM (Notes 8, 9).
Works with input resistance of
pin 9 to form part of control
path frequency weighting.
L8, C
L
4.7 mH,
0.015 μF
C9
0.047 μF
C10
1 μF
Set attack and decay time of
peak detector.
Sensitivity resistors set the
noise threshold. Reducing
attentuation causes larger
signals to be peak detected
and larger bandwidth in main
signal path. Total value of R1
+ R2 should equal 1 k
.
Forms RC roll-off with C8.
This is only required in FM
applications.
R1, R2
1 k
R8
100
Note 8:
Toko America Inc., 1250 Feehanville Drive, Mt. Prospect IL 60056
Note 9:
When FM applications are not required, pin 8 and pin 9 hook-up as
follows:
Circuit Operation
The LM1894 has two signal paths, a main signal path and a
bandwidth control path. The main path is an audio low pass
filter comprised of a gm block with a variable current, and an
op amp configured as an integrator. As seen in Figure 2 DC
feedback constrains the low frequency gain to A
= 1.
Above the cutoff frequency of the filter, the output decreases
at 6 dB/oct due to the action of the 0.0033 μF capacitor.
The purpose of the control paths is to generate a bandwidth
control signal which replicates the ear’s sensitivity to noise in
the presence of a tone. A single control path is used for both
channels to keep the stereo image from wandering. This is
done by adding the right and left channels together in the
summing amplifier of Figure 2 The R1, R2 resistor divider
adjusts the incoming noise level to open slightly the band-
width of the low pass filter. Control path gain is about 60 dB
and is set by the gain amplifier and peak detector gain. This
large gain is needed to ensure the low pass filter bandwidth
can be opened by very low noise floors. The capacitors
between the summing amplifier output and the peak detector
input determine the frequency weighting as shown in the
typical performance curves. The 1 μF capacitor at pin 10, in
conjunction with internal resistors, sets the attack and decay
times. The voltage is converted into a proportional current
which is fed into the gm blocks. The bandwidth sensitivity to
gm current is 33 Hz/μA. In FM stereo applications at 19 kHz
pilot filter is inserted between pin 8 and pin 9 as shown in
Figure 1
Figure 3 is an interesting curve and deserves some discus-
sion. Although the output of the DNR system is a linear
function of input signal, the 3 dB bandwidth is not. This is
due to the non-linear nature of the control path. The DNR
system has a uniform frequency response, but looking at the
3 dB bandwidth on a steady state basis with a single
frequency input can be misleading. It must be remembered
that a single input frequency can only give a single 3 dB
bandwidth and the roll-off from this point must be a smooth
6 dB/oct.
A more accurate evaluation of the frequency response can
be seen in Figure 4 In this case the main signal path is
frequency swept, while the control path has a constant fre-
quency applied. It can be seen that different control path
frequencies each give a distinctive gain roll-off.
Psychoacoustic Basics
The dynamic noise reduction system is a low pass filter that
has a variable bandwidth of 1 kHz to 30 kHz, dependent on
music spectrum. The DNR system operates on three prin-
ciples of psychoacoustics.
1. White noise can mask pure tones. The total noise energy
required to mask a pure tone must equal the energy of the
tone itself. Within certain limits, the wider the band of mask-
DS007918-6
L
www.national.com
5
相關PDF資料 |
PDF描述 |
|---|---|
| LM2202MX | Single Video Amplifier |
| LM2437NS | Driver |
| LM2439NS | Driver |
| LM2457 | |
| LM2465TA | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM18X12 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Color STN-LCD Module |
| LM18X94 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Color STN LCD Module |
| LM19 | 制造商:GENIE CCTV 功能描述:MONITOR 19" TFT SECURITY 制造商:GENIE CCTV 功能描述:MONITOR, 19", TFT SECURITY |
| LM-19 | 制造商:Mac8 功能描述:LEDpXy[T[ - KLEDaF3/ 5AKLEDsb`F-AtF - 125 -40 |
| LM19_07 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:2.4V, 10レA, TO-92 Temperature Sensor |
發布緊急采購，3分鐘左右您將得到回復。