參數資料
型號： LM2574N-15
廠商： ON SEMICONDUCTOR
元件分類： 穩壓器
英文描述： Dust cover; HRS No: 222-0135-3 00; No. of Positions: 6; Operating Temperature Range (degrees C): -25 to 60; General Description: Dust cover; Natural
中文描述： 1.8 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDIP8
封裝： PLASTIC, DIP-8
文件頁數： 10/24頁
文件大?。?/td> 397K
代理商： LM2574N-15
LM2574
10
MOTOROLA ANALOG IC DEVICE DATA
Procedure (Fixed Output Voltage Version)
In order to simplify the switching regulator design, a step–by–step
design procedure and example is provided.
Procedure
Example
Given Parameters:
Vout = Regulated Output Voltage (3.3 V, 5.0 V, 12 V or 15 V)
Vin(max) = Maximum Input Voltage
ILoad(max) = Maximum Load Current
Given Parameters:
Vout = 5.0 V
Vin(max) = 15 V
ILoad(max) = 0.4 A
1. Controller IC Selection
According to the required input voltage, output voltage and
current, select the appropriate type of the controller IC output
voltage version.
1. Controller IC Selection
According to the required input voltage, output voltage, current
polarity and current value, use the LM2574–5 controller IC.
2. Input Capacitor Selection (Cin)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +Vin and ground pin Gnd. This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
2. Input Capacitor Selection (Cin)
A 22
μ
F, 25 V aluminium electrolytic capacitor located near to
the input and ground pins provides sufficient bypassing.
3. Catch Diode Selection (D1)
A.
Since the diode maximum peak current exceeds the
regulator maximum load current, the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design the diode should have a
current rating equal to the maximum current limit of the
LM2574 to be able to withstand a continuous output short.
B.
The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A
.For this example the current rating of the diode is 1.0 A.
B.
Use a 20 V 1N5817 Schottky diode, or any of the
suggested fast recovery diodes shown in Table 1.
4. Inductor Selection (L1)
A.
According to the required working conditions, select the
correct inductor value using the selection guide from
Figures 19 to 23.
B.
From the appropriate inductor selection guide, identify the
inductance region intersected by the Maximum Input Voltage
line and the Maximum Load Current line. Each region is
identified by an inductance value and an inductor code.
C.
Select an appropriate inductor from the several different
manufacturers part numbers listed in Table 2. The designer
must realize that the inductor current rating must be higher
than the maximum peak current flowing through the inductor.
This maximum peak current can be calculated as follows:
where ton is the “on” time of the power switch and
V
out
V
in
For additional information about the inductor, see the inductor
section in the “EXTERNAL COMPONENTS” section of this
data sheet.
I
p
(
max
)
I
Load
(
max
)
V
in
V
out
t
on
2L
t
on
xf
osc
4. Inductor Selection (L1)
A.
Use the inductor selection guide shown in Figure 20.
B.
From the selection guide, the inductance area intersected
by the 15 V line and 0.4 A line is 330.
C.
Inductor value required is 330
μ
H. From Table 2, choose an
inductor from any of the listed manufacturers.
相關PDF資料
PDF描述
LM2574DW-ADJ EASY SWITCHER 0.5 A STEP-DOWN VOLTAGE REGULATOR
LM2574N-5 EASY SWITCHER 0.5 A STEP-DOWN VOLTAGE REGULATOR
LM2574N-3.3 EASY SWITCHER 0.5 A STEP-DOWN VOLTAGE REGULATOR
LM2574HVN-ADJ SIMPLE SWITCHER⑩ 0.5A Step-Down Voltage Regulator
LM2574M-ADJ SIMPLE SWITCHER⑩ 0.5A Step-Down Voltage Regulator
相關代理商/技術參數
參數描述
LM2574N-15/NOPB 功能描述:IC REG BUCK 15V 0.5A 8-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:SIMPLE SWITCHER® 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
LM2574N-15G 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:0.5 A, Adjustable Output Voltage, Step−Down Switching Regulator
LM2574N-3.3 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
LM2574N-3.3 NOPB 制造商:National Semiconductor 功能描述:Conv DC-DC Single Step Down 4V to 40V 8-Pin PDIP Rail
LM2574N-3.3/NOPB 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*