- 您現在的位置：買賣IC網 > PDF目錄358824 > LM2597 (National Semiconductor Corporation) Octal Buffers/Drivers With 3-State Outputs 20-SO -40 to 85 PDF資料下載
參數資料
| 型號： | LM2597 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Octal Buffers/Drivers With 3-State Outputs 20-SO -40 to 85 |
| 中文描述： | SIMPLE SWITCHER系列電源轉換器150千赫0.5A的降壓穩壓器的功能， |
| 文件頁數： | 12/34頁 |
| 文件大?。?/td> | 900K |
| 代理商： | LM2597 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
LM2597/LM2597HV Series Buck Regulator Design Procedure (Adjustable
Output)
PROCEDURE (Adjustable Output Voltage Version)
EXAMPLE (Adjustable Output Voltage Version)
Given:
V
OUT
= Regulated Output Voltage
V
IN
(max) = Maximum Input Voltage
I
LOAD
(max) = Maximum Load Current
F = Switching Frequency (Fixed at a nominal 150 kHz).
Given:
V
OUT
= 20V
V
IN
(max) = 28V
I
LOAD
(max) = 0.5A
F = Switching Frequency (Fixed at a nominal 150 kHz).
1. Programming Output Voltage
(Selecting R
1
and R
2
, as
shown in Figure 12)
Use the following formula to select the appropriate resistor
values.
Select a value for R
1
between 240
and 1.5 k
. The lower
resistor values minimize noise pickup in the sensitive feed-
back pin. (For the lowest temperature coefficient and the best
stability with time, use 1% metal film resistors.)
1. Programming Output Voltage
(Selecting R
1
and R
2
, as
shown in Figure 12)
Select R
1
to be 1 k
, 1%. Solve for R
2
.
R
2
= 1k (16.26 1) = 15.26k, closest 1% value is 15.4 k
.
R
2
= 15.4 k
.
2. Inductor Selection (L1)
A.
Calculate the inductor Volt microsecond constant E
T
(V
μs), from the following formula:
where V
SAT
= internal switch saturation voltage = 0.9V
and V
D
= diode forward voltage drop = 0.5V
B.
Use the E
T value from the previous formula and match
it with the E
T number on the vertical axis of the Inductor
Value Selection Guide shown in Figure 6
C.
on the horizontal axis, select the maximum load current.
D.
Identify the inductance region intersected by the E
T
value and the Maximum Load Current value. Each region is
identified by an inductance value and an inductor code (LXX).
E.
Select an appropriate inductor from the four manufacturer’s
part numbers listed in Figure 7
2. Inductor Selection (L1)
A.
Calculate the inductor Volt
microsecond constant (E
T),
B.
E
T = 35.2 (V
μs)
C.
I
LOAD
(max) = 0.5A
D.
From the inductor value selection guide shown in Figure 6
the inductance region intersected by the 35 (V
μs) horizontal
line and the 0.5A vertical line is 150 μH, and the inductor code
is L19.
E.
From the table in Figure 7 locate line L19, and select an
inductor part number from the list of manufacturers part num-
bers.
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM2597HV | |
| LM2608 | 400mA Sub-miniature, High Efficiency, Programmable DC-DC Converter with Linear Mode |
| LM2608ATL-1.3 | 400mA Sub-miniature, High Efficiency, Programmable DC-DC Converter with Linear Mode |
| LM2608ATL-1.8 | 400mA Sub-miniature, High Efficiency, Programmable DC-DC Converter with Linear Mode |
| LM2608ATLX-1.3 | 400mA Sub-miniature, High Efficiency, Programmable DC-DC Converter with Linear Mode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2597HVM-12 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2597HVM-12/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2597HVM-12/NOPB | 制造商:Texas Instruments 功能描述:DC/DC Converter IC |
| LM2597HVM-3.3 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2597HVM-3.3/NOPB | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。