- 您現在的位置：買賣IC網 > PDF目錄367562 > LM2651MTC-ADJ Current-Mode SMPS Controller PDF資料下載
參數資料
| 型號： | LM2651MTC-ADJ |
| 英文描述： | Current-Mode SMPS Controller |
| 中文描述： | 電流模式開關電源控制器 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 215K |
| 代理商： | LM2651MTC-ADJ |
Operation
OVERVIEW
The LM2650 uses two step-down conversion modes:
fixed-frquency pulse-width modulation (PWM) and hyster-
etic. It moves freely and automatically between them, using
PWM for moderate to heavy loads and hysteretic for light
loads.
For clarity, separate block diagrams for each conversion
mode have been included. See Figure 1 and Figure 2
Blocks used in both modes appear in both diagrams with the
same label. For example, both modes use the input buffer B.
To keep the diagrams simple, most power supply rails have
been omitted. R3, C10, R
C
, C
C
, C
B
, L1, R1, R2, and C
OUT
are outside the IC.
THE PWM CIRCUIT (
Figure 1
)
The PWM is a fixed-frequency, voltage-mode pulse-width
modulator. It consists of four functional blocks: an input
buffer, an error amplifier, a modulator, and a power stage.
1.
The input buffer B: B is a voltage follower. A fraction of
the output voltage is fed back to its noninverting input
FB. Circumventing B by using the COMP input as the
feedback input will cause the IC to malfunction.
2.
The error amplifier EA: EA is a voltage amplifier. It
subtracts the feedback voltage from the 1.25V reference
and amplifies the difference to produce an error voltage
for the control loop. For the purpose of loop compensa-
tion, EA is typically configured as an integrator. In this
configuration, a capacitor C
C
and a resistor R
C
are
connected in series between the inverting input COMP
and the output terminal EA OUT. The capacitor and the
internal 6.5k
resistor create a pole, while the capacitor
and series resistor create a zero.
3.
The modulator: The modulator is the heart of the PWM
circuit. It consists of the 90 kHz oscillator, the voltage
comparator C1, and output logic represented here as a
simple SR latch.
The modulator generates a continuous stream of rect-
angular, signal-level. It generates the pulses at a fixed
frequency, and it modulates or varies their widths in
response to variations in the error voltage. The pulses
appear at Q, the output of the SR latch. An increase in
the error voltage results in a proportional increase in the
pulse widths, and, conversely, a decrease in the error
voltage results in a proportional decrease in the pulse
widths.
The oscillator produces a 90 kHz sawtooth that ramps
between 1V and 2V. At the beginning of each ramp, the
oscillator sets the SR latch sending Q high. As the ramp
voltage surpasses the error voltage, C1 resets the SR
latch sending Q low. An increase in the error voltage
increases the time between the setting and the resetting
of the SR latch which , in turn, results in an equal
increase in pulse widths: that is, an equal increase in the
time Q spends high in each cycle. A decrease in the
error voltage has the opposite effect on the pulse widths
as it decreases the time between the setting and reset-
ting of the SR latch.
4.
The power stage: The power stage puts some punch
between the output of the modulator by translating the
stream of signal-level pulses generated by the modula-
tor into a stream of power pulses that swing from ground
up to the input voltage while sinking and sourcing as
much as 3.5A. The power stage consists of two gate
drivers DH and DL, two linear voltage regulators VRegH
and VRegL, and two NMOS power FETs Q1 and Q2.
The power pulses appear at the SW mode. When Q
goes high, DL drives the gate of Q2 low turning Q23 off.
While Q2 turns off, the SW potential may remain at just
below ground as the body diode of Q2 conducts what
was previously reverse current (source-to-drain) in Q2,
or the SW potential may swing up to just above the input
voltage as the body diode of Q1 conducts what was
previously forward current (drain-to-source) in Q2.About
50 ns after Q goes high, DH drives the gate of Q1 high
turning Q1 on. If the task remains, Q1 pulls the SW
potential up, if not, Q1 simply takes over the conduction
responsibility from its own body diode. When Q goes
low, the inverse action occurs resulting in the SW poten-
tial swinging from the input voltage to the ground. The 50
ns delay between one switch beginning to turn off and
the other switch beginning to turn on prevents the
switches from
″
shooting through
″
directly from the input
supply to the ground.
The PWM circuit drives the pulse stream into the
low-pass filter made up of L1 and C
. The filter
passed the DC component of the stream and attenuates
the AC components. The output of the filter is the DC
voltage V
superimposed with a small ripple voltage.
Since the DC component of any periodic waveforms the
average value of the waveform, V
OUT
can be found
using:
(1)
Here T is the switching period in seconds V(t) is the pulse
stream. Under DC steady-state conditions, (1) yields
(2)
Here V
is the input voltage, and therefore the height of the
pulses, in volts, is the width of the pulses in seconds, and D
is the ratio of t
to T, the duty or the duty cycle.
The output voltage is programmed using the resistive divider
made up for R1 and R2,
(3)
As Q1 turns on, its source voltage swings up to just below
the input voltage. The LM2650 uses a simple technique
called
″
bootstrapping
″
to pull the positive supply rail of DH
(at BOOT) up along with the source voltage of Q1, but to a
voltage above the input voltage. Because the source of Q1
and the positive supply rail of DH make the same voltage
swing together, DH maintains the positive gate-to-source
voltage required to turn Q1 on. Q12 plays an active role in
pulling the supply rail of DH up and is therefore said to pull
itself up by its
″
bootstraps
″
, thus the name of the technique
and of the BOOT pin.
In the typical application, a capacitor CB is connected out-
side the IC between the BOOT and SW pins. When Q2 is on,
the input supply charges CB through VRegH and the internal
diode D.
THE HYSTERETIC CIRCUIT AND LOOP (
Figure 2
)
Except for C2, the hysteretic circuit borrows all its circuit
blocks from the PWM circuit.
The hysteretic comparator C2 is a voltage comparator with
built-in hysteresis V
HYST
of typically 30mV centered at
1.25V.
L
www.national.com
7
相關PDF資料 |
PDF描述 |
|---|---|
| LM2651MTCX-1.8 | Current-Mode SMPS Controller |
| LM2651MTCX-2.5 | Current-Mode SMPS Controller |
| LM2651MTCX-3.3 | Current-Mode SMPS Controller |
| LM2651MTCX-ADJ | Current-Mode SMPS Controller |
| LM2653 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2651MTC-ADJ | 制造商:Texas Instruments 功能描述:SWITCHING REG 1.5A ADJ SMD 2651 |
| LM2651MTC-ADJ/NOPB | 功能描述:直流/直流開關轉換器 1.5A HIGH EFFICIENCY SWITCHING REG RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| LM2651MTCX-1.8 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.5A High Efficiency Synchronous Switching Regulator |
| LM2651MTCX-1.8/J7001113 | 制造商:Texas Instruments 功能描述: |
| LM2651MTCX-1.8/NOPB | 功能描述:IC REG BUCK SYNC 1.8V 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
發布緊急采購，3分鐘左右您將得到回復。