- 您現在的位置：買賣IC網 > PDF目錄367562 > LM2686MTC DC-to-DC Voltage Converter PDF資料下載
參數資料
| 型號： | LM2686MTC |
| 英文描述： | DC-to-DC Voltage Converter |
| 中文描述： | 型DC - DC電壓轉換器 |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 244K |
| 代理商： | LM2686MTC |
Detailed Device Description
The LM2685 CMOS charge pump voltage converter oper-
ates as an input voltage doubler, +5V regulator and inverter
for an input voltage in the range of +2.85V to +6.5V. It deliv-
ers maximum load currents of 50mA and 15mA for the regu-
lated +5V and the inverted output voltages respectively, with
an operating current of only 800μA. It also has a typical shut-
down current of 6μA. All these performance qualities make
the LM2685 an ideal device for battery powered systems.
The LM2685 has three main functional blocks: a voltage
doubler, a low dropout (LDO) regulator, and a voltage in-
verter. Figure 1shows the LM2685 functional block diagram.
Voltage Doubler
The voltage doubler stage doubles the input voltage V
,
within the range of +2.85V to +5.4V. For V
above 5.4V, the
doubler shuts off and the input voltage is passed directly to
V
DBL
via an internal power switch.
The doubler contains four large CMOS switches which are
switched in a sequence to double the input supply voltage.
Figure 2illustrates the voltage conversion scheme. When S2
and S4 are closed, C1 charges to the supply voltage V
.
During this time interval, switches S1 and S3 are open. In the
next time interval, S2 and S4 are opened at the same time,
S1 and S3 are closed, the sum of the input voltage V
and
the voltage across C1 gives the 2V
and the voltage across
C2 gives the 2V
at V
output. V
supplies the LDO
regulator. It is recommended not to load V
DBL
when V
05
has
a load of 50mA. For proper operation, the sum of V
DBL
and
V
05
loads must not be more than 50mA.
The Schottky diode D1 is only needed for start-up. The inter-
nal oscillator circuit uses the V
DBL
and GND pins. The volt-
age across them must be larger than 1.8V to ensure the op-
eration of the oscillator. During start-up, D1 is used to charge
up the voltage at V
pin to start the oscillator; it also pro-
tects the device from turning on its own parasitic diode and
potentially latching up. The diode should have enough cur-
rent carrying capability to change capacitor C3 at start-up, as
well as a low forward voltage to prevent the internal parasitic
diode from turning on. A Schottky diode like 1N5817 can be
used for most applications. If the input ramp is less than
10V/ms, a smaller schottky diode like MBR0520LT1 can be
used to reduce the circuit size.
+5 LDO Regulator
V
DBL
is the input to an LDO regulator that regulates it to a +5
output voltage at V
. V
is tied to V
through a series
switch PSW. The LDO output capacitor (4.7μF Tantalum)
may be tied to either V
05
or V
PSW
.
Inverter
From the V
output, a 5V output is created at V
by
means of an inverting charge pump. This negative output is
unregulated, meaning that it’s output will droop as the load
current at V
increases. The inverter contains four large
CMOS switches which are in a sequence to invert the input
supply voltage. Figure 3 illustrates the voltage conversion
scheme. When S1 and S3 are closed, C1 charges to the
supply voltage V
. During this time interval, switches S2
and S4 are open. In the second time interval, S1 and S3 are
open;at the same time, S2 and S4 are closed, C1 is charging
C2. After a number of cycles, the voltage cross C2 will be
pumped to V
. Since the anode of C2 is connected to
ground, the output at the cathode of C2 equals (V
) when
there is no load current. The output voltage drop when a load
DS101100-3
FIGURE 1. Functional Block Diagram
DS101100-4
FIGURE 2. Voltage Doubler Principle
L
www.national.com
6
相關PDF資料 |
PDF描述 |
|---|---|
| LM2686MTCX | DC-to-DC Voltage Converter |
| LM2687 | |
| LM2687MM | IC-SWT CAP VOLT INVERTER |
| LM2687MMX | DC-to-DC Voltage Converter |
| LM2688M-ADJ | Voltage-Mode SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2686MTC | 制造商:Texas Instruments 功能描述:VOLT CONVERTER SMD 2686 TSSOP14 |
| LM2686MTC/NOPB | 功能描述:IC REG SWITCHED CAP DBL 14-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2686MTCX/NOPB | 功能描述:IC REG SWITCHED CAP DBL 14-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2687LD | 制造商:Texas Instruments 功能描述: |
| LM2687LD/NOPB | 功能描述:IC REG SWITCHD CAP INV ADJ 8-LLP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
發布緊急采購，3分鐘左右您將得到回復。