- 您現在的位置：買賣IC網 > PDF目錄358828 > LM2716 (National Semiconductor Corporation) Dual (Step-up and Step-down) PWM DC/DC Converter PDF資料下載
參數資料
| 型號： | LM2716 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Dual (Step-up and Step-down) PWM DC/DC Converter |
| 中文描述： | 雙（升壓和降壓）PWM直流/直流轉換器 |
| 文件頁數： | 9/17頁 |
| 文件大小： | 563K |
| 代理商： | LM2716 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Buck Operation
PROTECTION (BOTH REGULATORS)
The LM2716 has dedicated protection circuitry running dur-
ing normal operation to protect the IC. The Thermal Shut-
down circuitry turns off the power devices when the die
temperature reaches excessive levels. The UVP comparator
protects the power devices during supply power startup and
shutdown to prevent operation at voltages less than the
minimum input voltage. The OVP comparator is used to
prevent the output voltage from rising at no loads allowing
full PWM operation over all load conditions. The LM2716
also features a shutdown mode for each converter decreas-
ing the supply current to 9μA (both in shutdown mode).
CONTINUOUS CONDUCTION MODE
The LM2716 contains a current-mode, PWM buck regulator.
A buck regulator steps the input voltage down to a lower
output voltage. In continuous conduction mode (when the
inductor current never reaches zero at steady state), the
buck regulator operates in two cycles. The power switch is
connected between V
IN
and SW1.
In the first cycle of operation the transistor is closed and the
diode is reverse biased. Energy is collected in the inductor
and the load current is supplied by C
OUT
and the rising
current through the inductor.
During the second cycle the transistor is open and the diode
is forward biased due to the fact that the inductor current
cannot instantaneously change direction. The energy stored
in the inductor is transferred to the load and output capacitor.
The ratio of these two cycles determines the output voltage.
The output voltage is defined approximately as:
where D is the duty cycle of the switch, D and D' will be
required for design calculations.
DESIGN PROCEDURE
This section presents guidelines for selecting external com-
ponents.
INPUT CAPACITOR
A low ESR aluminum, tantalum, or ceramic capacitor is
needed betwen the input pin and power ground. This capaci-
tor prevents large voltage transients from appearing at the
input. The capacitor is selected based on the RMS current
and voltage requirements. The RMS current is given by:
The RMS current reaches its maximum (I
OUT
/2) when
V
IN
equals 2V
OUT
. This value should be increased by 50% to
account for the ripple current increase due to the boost
regulator. For an aluminum or ceramic capacitor, the voltage
rating should be at least 25% higher than the maximum input
voltage. If a tantalum capacitor is used, the voltage rating
required is about twice the maximum input voltage. The
tantalum capacitor should be surge current tested by the
manufacturer to prevent being shorted by the inrush current.
The minimum capacitor value should be 47μF for lower
output load current applications and less dynamic (quickly
changing) load conditions. For higher output current applica-
tions or dynamic load conditions a 68μF to 100μF low ESR
capacitor is recommended. It is also recommended to put a
small ceramic capacitor (0.1 μF) between the input pin and
ground pin to reduce high frequency spikes.
INDUCTOR SELECTION
The most critical parameters for the inductor are the induc-
tance, peak current and the DC resistance. The inductance
is related to the peak-to-peak inductor ripple current, the
input and the output voltages:
A higher value of ripple current reduces inductance, but
increases the conductance loss, core loss, current stress for
the inductor and switch devices. It also requires a bigger
output capacitor for the same output voltage ripple require-
ment. A reasonable value is setting the ripple current to be
30% of the DC output current. Since the ripple current in-
creases with the input voltage, the maximum input voltage is
always used to determine the inductance. The DC resistance
of the inductor is a key parameter for the efficiency. Lower
DC resistance is available with a bigger winding area.Agood
tradeoff between the efficiency and the core size is letting the
inductor copper loss equal 2% of the output power.
OUTPUT CAPACITOR
The selection of C
is driven by the maximum allowable
output voltage ripple. The output ripple in the constant fre-
quency, PWM mode is approximated by:
The ESR term usually plays the dominant role in determining
the voltage ripple. A low ESR aluminum electrolytic or tanta-
lum capacitor (such as Nichicon PL series, Sanyo OS-CON,
Sprague 593D, 594D, AVX TPS, and CDE polymer alumi-
num) is recommended. An electrolytic capacitor is not rec-
ommended for temperatures below 25C since its ESR
rises dramatically at cold temperature. A tantalum capacitor
has a much better ESR specification at cold temperature and
is preferred for low temperature applications.
BOOT CAPACITOR
A 3.3 nF ceramic capacitor is recommended for the boot-
strap capacitor.
SOFT-START CAPACITOR (BOTH REGULATORS)
The SS pins are used to tailor the soft-start for a specific
application. A current source charges the external soft-start
capacitor, C
SS
. The soft-start time can be estimated as:
T
SS
= C
SS
*0.6V/I
SS
Soft-start times may be implemented using the SS pin and a
capacitor C
SS
.
When programming the softstart time, simply use the equa-
tion given in the
Soft-Start Capacitor
section above. This
equation uses the typical room temperature value of the soft
start current to set the soft start time.
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LM2717 | Dual Step-down DC/DC Converter |
| LM2717MT | Dual Step-down DC/DC Converter |
| LM2717MTX | Dual Step-down DC/DC Converter |
| LM2731XMF | 0.6/1.6 MHz Boost Converters With 22V Internal FET Switch in SOT-23 |
| LM2731XMFX | 0.6/1.6 MHz Boost Converters With 22V Internal FET Switch in SOT-23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2716MT | 制造商:Texas Instruments 功能描述:LCD BUCK, BOOSTER, 2716, TSSOP24 |
| LM2716MT/NOPB | 功能描述:IC REG BUCK BST FIX/ADJ 24-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:3.3V 輸入電壓:4.5 V ~ 24 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:125mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 包裝:Digi-Reel® 供應商設備封裝:SOT-6 其它名稱:MAX1836EUT33#TG16DKR |
| LM2716MT-ADJ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dual (Step-up and Step-down) PWM DC/DC Converter |
| LM2716MTEV | 功能描述:電源管理IC開發工具 LM2716MT EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM2716MTX | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。