- 您現在的位置：買賣IC網 > PDF目錄358828 > LM2734YMK (NATIONAL SEMICONDUCTOR CORP) Thin SOT23 1A Load Step-Down DC-DC Regulator PDF資料下載
參數資料
| 型號： | LM2734YMK |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Thin SOT23 1A Load Step-Down DC-DC Regulator |
| 中文描述： | 2.5 A SWITCHING REGULATOR, 660 kHz SWITCHING FREQ-MAX, PDSO6 |
| 封裝： | TSOT-23, 6 PIN |
| 文件頁數： | 11/22頁 |
| 文件大?。?/td> | 459K |
| 代理商： | LM2734YMK |
Design Guide
(Continued)
OUTPUT VOLTAGE
The output voltage is set using the following equation where
R2 is connected between the FB pin and GND, and R1 is
connected between V
O
and the FB pin. A good value for R2
is 10k
.
PCB Layout Considerations
When planning layout there are a few things to consider
when trying to achieve a clean, regulated output. The most
important consideration when completing the layout is the
close coupling of the GND connections of the C
capacitor
and the catch diode D1. These ground ends should be close
to one another and be connected to the GND plane with at
least two through-holes. Place these components as close to
the IC as possible. Next in importance is the location of the
GND connection of the C
capacitor, which should be
near the GND connections of C
IN
and D1.
There should be a continuous ground plane on the bottom
layer of a two-layer board except under the switching node
island.
The FB pin is a high impedance node and care should be
taken to make the FB trace short to avoid noise pickup and
inaccurate regulation. The feedback resistors should be
placed as close as possible to the IC, with the GND of R2
placed as close as possible to the GND of the IC. The V
OUT
trace to R1 should be routed away from the inductor and any
other traces that are switching.
High AC currents flow through the V
IN
, SW and V
OUT
traces,
so they should be as short and wide as possible. However,
making the traces wide increases radiated noise, so the
designer must make this trade-off. Radiated noise can be
decreased by choosing a shielded inductor.
The remaining components should also be placed as close
as possible to the IC. Please see Application Note AN-1229
for further considerations and the LM2734 demo board as an
example of a four-layer layout.
L
www.national.com
11
相關PDF資料 |
PDF描述 |
|---|---|
| LM2734XMKX | Thin SOT23 1A Load Step-Down DC-DC Regulator |
| LM2734XMK | Thin SOT23 1A Load Step-Down DC-DC Regulator |
| LM2734 | Thin SOT23 1A Load Step-Down DC-DC Regulator |
| LM2736 | Thin SOT23 750mA Load Step-Down DC-DC Regulator |
| LM2736XMK | Thin SOT23 750mA Load Step-Down DC-DC Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2734YMK/NOPB | 功能描述:直流/直流開關調節器 1A LOAD STEP-DOWN DC-DC REG RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2734YMKX | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2734YMKX/NOPB | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| LM2734YQMK | 制造商:Texas Instruments 功能描述:DC DC REG, BUCK, 1A, 550KHZ, 6TSOT 制造商:Texas Instruments 功能描述:DC DC REG, BUCK, 1A, 550KHZ, 6TSOT; Primary Input Voltage:20V; No. of Outputs:1; Output Voltage:18V; Output Current:1A; Voltage Regulator Case Style:SOT-23; No. of Pins:6; Operating Temperature Min:-40C; Operating Temperature ;RoHS Compliant: Yes |
| LM2734YQMK/NOPB | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。