參數資料
型號： LM2746MXAX
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： Low Voltage N-Channel MOSFET Synchronous Buck Regulator Controller
中文描述： SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO14
封裝： PLASTIC, TSSOP-14
文件頁數： 16/24頁
文件大小： 1087K
代理商： LM2746MXAX
Application Information
(Continued)
4SP560M electrolytic capacitor will give an equivalent ESR
of 14m
. The capacitance of 560 μF is enough to supply
energy even to meet severe load transient demands.
MOSFETs
Selection of the power MOSFETs is governed by a tradeoff
between cost, size, and efficiency. One method is to deter-
mine the maximum cost that can be endured, and then
select the most efficient device that fits that price. Breaking
down the losses in the high-side and low-side MOSFETs and
then creating spreadsheets is one way to determine relative
efficiencies between different MOSFETs. Good correlation
between the prediction and the bench result is not guaran-
teed, however. Single-channel buck regulators that use a
controller IC and discrete MOSFETs tend to be most efficient
for output currents of 2-10A.
Losses in the high-side MOSFET can be broken down into
conduction loss, gate charging loss, and switching loss.
Conduction, or I
2
R loss, is approximately:
P
C
= D (I
O2
x R
x 1.3)
(High-Side MOSFET)
P
C
= (1 - D) x (I
O2
x R
x 1.3)
(Low-Side MOSFET)
In the above equations the factor 1.3 accounts for the in-
crease in MOSFET R
DSON
due to heating. Alternatively, the
1.3 can be ignored and the R
DSON
of the MOSFET estimated
using the R
DSON
Vs. Temperature curves in the MOSFET
datasheets.
Gate charging loss results from the current driving the gate
capacitance of the power MOSFETs, and is approximated
as:
P
GC
= n x (V
DD
) x Q
G
x f
SW
where ‘n’ is the number of MOSFETs (if multiple devices
have been placed in parallel), V
is the driving voltage (see
MOSFET Gate Drivers section) and Q
is the gate charge
of the MOSFET. If different types of MOSFETs are used, the
‘n’ term can be ignored and their gate charges simply
summed to form a cumulative Q
. Gate charge loss differs
from conduction and switching losses in that the actual
dissipation occurs in the LM2746, and not in the MOSFET
itself.
Switching loss occurs during the brief transition period as the
high-side MOSFET turns on and off, during which both cur-
rent and voltage are present in the channel of the MOSFET.
It can be approximated as:
P
SW
= 0.5 x V
IN
x I
O
x (t
r
+ t
f
) x f
SW
where t
and t
are the rise and fall times of the MOSFET.
Switching loss occurs in the high-side MOSFET only.
For this example, the maximum drain-to-source voltage ap-
plied to either MOSFET is 3.6V. The maximum drive voltage
at the gate of the high-side MOSFET is 3.1V, and the maxi-
mum drive voltage for the low-side MOSFET is 3.3V. Due to
the low drive voltages in this example, a MOSFET that turns
on fully with 3.1V of gate drive is needed. For designs of 5A
and under, dual MOSFETs in SO-8 provide a good tradeoff
between size, cost, and efficiency.
Support Components
C
IN
2
- A small (0.1 to 1 μF) ceramic capacitor should be
placed as close as possible to the drain of the high-side
MOSFET and source of the low-side MOSFET (dual MOS-
FETs make this easy). This capacitor should be X5R type
dielectric or better.
R
CC
, C
CC
- These are standard filter components designed to
ensure smooth DC voltage for the chip supply. R
CC
should
be 1-10
. C
CC
should 1 μF, X5R type or better.
C
BOOT
- Bootstrap capacitor, typically 100nF.
R
PULL-UP
– This is a standard pull-up resistor for the open-
drain power good signal (PWGD). The recommended value
is 10 k
connected to V
CC
. If this feature is not necessary,
the resistor can be omitted.
D
-Asmall Schottky diode should be used for the bootstrap.
It allows for a minimum drop for both high and low-side
drivers. The MBR0520 or BAT54 work well in most designs.
R
- Resistor used to set the current limit. Since the design
calls for a peak current magnitude (I
+0.5*
I
) of 4.8A,
a safe setting would be 6A. (This is below the saturation
current of the output inductor, which is 7A.) Following the
equation from the Current Limit section, a 1.3k
resistor
should be used.
R
- This resistor is used to set the switching frequency of
the chip. The resistor value is calculated from equation in
Normal Operation section. For 300 kHz operation, a 97.6 k
resistor should be used.
C
SS
- The soft-start capacitor depends on the user require-
ments and is calculated based on the equation given in the
section titled
START UP/SOFT-START
. Therefore, for a
700μs delay, a 12nF capacitor is suitable.
Control Loop Compensation
The LM2746 uses voltage-mode (‘VM’) PWM control to cor-
rect changes in output voltage due to line and load tran-
sients. One of the attractive advantages of voltage mode
control is its relative immunity to noise and layout. However
VM requires careful small signal compensation of the control
loop for achieving high bandwidth and good phase margin.
The control loop is comprised of two parts. The first is the
power stage, which consists of the duty cycle modulator,
output inductor, output capacitor, and load. The second part
is the error amplifier, which for the LM2746 is a 9MHz
op-amp used in the classic inverting configuration.
Figure 12
shows the regulator and control loop components.
L
www.national.com
16
相關PDF資料
PDF描述
LM2753SD High Power Switched Capacitor Voltage Convertor/Flash LED Driver
LM2753 High Power Switched Capacitor Voltage Convertor/Flash LED Driver
LM2753SDX High Power Switched Capacitor Voltage Convertor/Flash LED Driver
LM2765 Switched Capacitor Voltage Converter
LM2765M6 Switched Capacitor Voltage Converter
相關代理商/技術參數
參數描述
LM2746MXAX/NOPB 功能描述:IC REG CTRLR BUCK PWM VM 14TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF)
LM2747 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Synchronous Buck Controller with Pre-bias Startup, and Optional Clock Synchronization
LM2747-19AEVAL 功能描述:電源管理IC開發工具 LM2747 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LM2747EVAL 功能描述:電源管理IC開發工具 LM2747EVAL EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
LM2747MTC 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*