- 您現在的位置：買賣IC網 > PDF目錄6140 > LM2904WDT (Rohm Semiconductor)IC OPAMP DUAL 32V 8-SOIC PDF資料下載
參數資料
| 型號： | LM2904WDT |
| 廠商： | Rohm Semiconductor |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP DUAL 32V 8-SOIC |
| 標準包裝： | 1 |
| 系列： | 簽名 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 轉換速率： | 0.6 V/µs |
| 增益帶寬積： | 1.1MHz |
| 電流 - 輸入偏壓： | 20nA |
| 電壓 - 輸入偏移： | 2000µV |
| 電流 - 電源： | 1mA |
| 電流 - 輸出 / 通道： | 20mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 32 V，±1.5 V ~ 16 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1377 (CN2011-ZH PDF) |
| 其它名稱： | LM2904WDTDKR |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
Technical Note
14/17
LM358DT/PT/ST/WDT/WPT,LM2904DT/PT/ST/WDT/WPT
LM324DT/PT/WDT,LM2902DT/PT/WDT
www.rohm.com
2011.06 - Rev.B
2011 ROHM Co., Ltd. All rights reserved.
●Description of Electrical Characteristics
Described below are descriptions of the relevant electrical terms
Please note that item names, symbols and their meanings may differ from those on another manufacturer’s documents.
1.Absolute maximum ratings
The absolute maximum ratings are values that should never be exceeded, since doing so may result in deterioration of electrical characteristics or damage to
the part itself as well as peripheral components.
1.1 Power supply voltage (Vcc
+/Vcc-)
Expresses the maximum voltage that can be supplied between the positive and negative supply terminals without causing deterioration of the electrical
characteristics or destruction of the internal circuitry.
1.2 Differential input voltage (VID)
Indicates the maximum voltage that can be supplied between the non-inverting and inverting terminals without damaging the IC.
1.3 Input common-mode voltage range (VICM)
Signifies the maximum voltage that can be supplied to non-inverting and inverting terminals without causing deterioration of the characteristics or damage to
the IC itself. Normal operation is not guaranteed within the common-mode voltage range of the maximum ratings – use within the input common-mode
voltage range of the electric characteristics instead.
1.4 Operating and storage temperature ranges (Topr,Tstg)
The operating temperature range indicates the temperature range within which the IC can operate. The higher the ambient temperature, the lower the power
consumption of the IC. The storage temperature range denotes the range of temperatures the IC can be stored under without causing excessive
deterioration of the electrical characteristics.
1.5 Power dissipation (Pd)
Indicates the power that can be consumed by a particular mounted board at ambient temperature (25℃). For packaged products, Pd is determined by the
maximum junction temperature and the thermal resistance.
2. Electrical characteristics
2.1 Input offset voltage (VIO)
Signifies the voltage difference between the non-inverting and inverting terminals. It can be thought of as the input voltage difference required for setting the
output voltage to 0 V.
2.2 Input offset voltage drift (DVIO)
Denotes the ratio of the input offset voltage fluctuation to the ambient temperature fluctuation.
2.3 Input offset current (IIO)
Indicates the difference of input bias current between the non-inverting and inverting terminals.
2.4 Input offset current drift (DIIO)
Signifies the ratio of the input offset current fluctuation to the ambient temperature fluctuation.
2.5 Input bias current (IIB)
Denotes the current that flows into or out of the input terminal, it is defined by the average of the input bias current at the non-inverting terminal and the input
bias current at the inverting terminal.
2.6 Circuit current (ICC)
Indicates the current of the IC itself that flows under specified conditions and during no-load steady state.
2.7 High level output voltage/low level output voltage (VOH/VOL)
Signifying the voltage range that can be output under specified load conditions, it is in general divided into high level output voltage and low level output
voltage. High level output voltage indicates the upper limit of the output voltage, while low level output voltage the lower limit.
2.8 Large signal voltage gain (AVD)
The amplifying rate (gain) of the output voltage against the voltage difference between non-inverting and inverting terminals, it is (normally) the amplifying
rate (gain) with respect to DC voltage.
AVD = (output voltage fluctuation) / (input offset fluctuation)
2.9 Input common-mode voltage range (VICM)
Indicates the input voltage range under which the IC operates normally.
2.10 Common-mode rejection ratio (CMRR)
Signifies the ratio of fluctuation of the input offset voltage when the in-phase input voltage is changed (DC fluctuation).
CMRR = (change in input common-mode voltage) / (input offset fluctuation)
2.11 Power supply rejection ratio (SVR)
Denotes the ratio of fluctuation of the input offset voltage when supply voltage is changed (DC fluctuation).
SVR = (change in power supply voltage) / (input offset fluctuation)
2.12 Output source current/ output sink current (IOH/IOL)
The maximum current that can be output under specific output conditions, it is divided into output source current and output sink current. The output source
current indicates the current flowing out of the IC, and the output sink current the current flowing into the IC.
2.13 Channel separation (VO1/VO2)
Expresses the amount of fluctuation of the input offset voltage or output voltage with respect to the change in the output voltage of a driven channel.
2.14 Slew rate (SR)
Indicates the time fluctuation ratio of the output voltage when an input step signal is supplied.
2.15 Gain bandwidth product (GBP)
The product of the specified signal frequency and the gain of the op-amp at such frequency, it gives the approximate value of the frequency where the gain of
the op-amp is 1 (maximum frequency, and unity gain frequency).
相關PDF資料 |
PDF描述 |
|---|---|
| 929834-02-07-RK | CONN HEADER .100 SNGL STR 7POS |
| MOV-10D681K | VARISTOR 680V 10MM RADIAL |
| LM2904VQDR | IC OPAMP DUAL 32V 8-SOIC |
| 929400-01-07-RK | CONN HEADER .100 SNGL STR 7POS |
| MOV-10D621K | VARISTOR 620V 10MM RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2904WHD | 功能描述:運算放大器 - 運放 Low power dual opamp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM2904WHDT | 功能描述:運算放大器 - 運放 E-EPROM RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LM2904WHYD | 制造商:STMicroelectronics 功能描述: |
| LM2904WHYDT | 功能描述:IC OP AMP DUAL GP 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:2 V/µs 增益帶寬積:5MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:1500µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:100mA 電壓 - 電源，單路/雙路(±):4 V ~ 36 V，±2 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:14-DIP（0.300"，7.62mm） 供應商設備封裝:14-PDIP 包裝:管件 產品目錄頁面:1130 (CN2011-ZH PDF) 其它名稱:MC33179PGOS |
| LM2904WHYST | 功能描述:General Purpose Amplifier 2 Circuit 8-SO 制造商:stmicroelectronics 系列:汽車級，AEC-Q100 包裝:剪切帶（CT） 零件狀態:在售 放大器類型:通用 電路數:2 輸出類型:- 壓擺率:0.6 V/μs 增益帶寬積:1.1MHz -3db 帶寬:- 電流 - 輸入偏置:20nA 電壓 - 輸入失調:2mV 電流 - 電源:700μA 電流 - 輸出/通道:20mA 電壓 - 電源，單/雙（±）:3 V ~ 30 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SO 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。