- 您現在的位置：買賣IC網 > PDF目錄358836 > LM2937ES-5.0 (NATIONAL SEMICONDUCTOR CORP) Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection PDF資料下載
參數資料
| 型號： | LM2937ES-5.0 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| 中文描述： | 5 V FIXED POSITIVE LDO REGULATOR, 1 V DROPOUT, PSSO3 |
| 封裝： | PLASTIC, TO-263, 3 PIN |
| 文件頁數： | 7/11頁 |
| 文件大小： | 300K |
| 代理商： | LM2937ES-5.0 |
θ
is specified numerically by the heatsink manufacturer
in the catalog, or shown in a curve that plots temperature rise
vs power dissipation for the heatsink.
HEATSINKING TO-263 AND SOT-223 PACKAGE PARTS
Both the TO-263 (“S”) and SOT-223 (“MP”) packages use a
copper plane on the PCB and the PCB itself as a heatsink.
To optimize the heat sinking ability of the plane and PCB,
solder the tab of the package to the plane.
Figure 3shows for the TO-263 the measured values of
θ
for different copper area sizes using a typical PCB with 1
ounce copper and no solder mask over the copper area used
for heatsinking.
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. It should also
be observed that the minimum value of
θ
(JA)
for the TO-263
package mounted to a PCB is 32C/W.
As a design aid, Figure 4 shows the maximum allowable
power dissipation compared to ambient temperature for the
TO-263 device (assuming
θ
is 35C/W and the maxi-
mum junction temperature is 125C).
Figure 5 and Figure 6 show the information for the SOT-223
package. Figure 6 assumes a
θ
of 74C/W for 1 ounce
copper and 51C/W for 2 ounce copper and a maximum
junction temperature of 125C.
Please see AN1028 for power enhancement techniques to
be used with the SOT-223 package.
SOT-223 SOLDERING RECOMMENDATIONS
It is not recommended to use hand soldering or wave solder-
ing to attach the small SOT-223 package to a printed circuit
board. The excessive temperatures involved may cause
package cracking.
Either vapor phase or infrared reflow techniques are pre-
ferred soldering attachment methods for the SOT-223 pack-
age.
DS100113-20
FIGURE 3.
θ
(JA)
vs Copper (1 ounce) Area for the
TO-263 Package
DS100113-21
FIGURE 4. Maximum Power Dissipation vs T
AMB
for
the TO-263 Package
DS100113-22
FIGURE 5.
θ
(JA)
vs Copper (2 ounce) Area for the
SOT-223 Package
DS100113-23
FIGURE 6. Maximum Power Dissipation vs T
AMB
for
the SOT-223 Package
7
www.national.com
相關PDF資料 |
PDF描述 |
|---|---|
| LM2937ES-8.0 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LM2937ET-10 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LM2937ET-12 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LM2937ET-15 | Cap-Free, NMOS, 150mA Low Dropout Regulator with Reverse Current Protection |
| LM2937ET-3.3 | 400mA and 500mA Voltage Regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2937ES50NOPB | 制造商:NATIONAL 功能描述:Pb Free |
| LM2937ES-8.0 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM2937ES-8.0/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LM2937ES-8.0/NOPB | 制造商:Texas Instruments 功能描述:Voltage Regulator IC |
| LM2937ESX-10/NOPB | 功能描述:IC REG LDO 10V .5A TO-263 RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:4V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.28V @ 150mA 穩壓器數量:1 電流 - 輸出:150mA 電流 - 限制（最小）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:5-VFBGA 供應商設備封裝:5-uSMD 包裝:Digi-Reel® 其它名稱:LP2985AIBP-4.0DKR |
發布緊急采購，3分鐘左右您將得到回復。