- 您現在的位置：買賣IC網 > PDF目錄358839 > LM3200TLX (NATIONAL SEMICONDUCTOR CORP) Miniature, Adjustable, Step-Down DC-DC Converter with Bypass Mode for RF Power Amplifiers PDF資料下載
參數資料
| 型號： | LM3200TLX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Miniature, Adjustable, Step-Down DC-DC Converter with Bypass Mode for RF Power Amplifiers |
| 中文描述： | 1.2 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, PBGA10 |
| 封裝： | ROHS COMPLIANT, THIN MICRO SMD, 10 PIN |
| 文件頁數： | 4/15頁 |
| 文件大?。?/td> | 885K |
| 代理商： | LM3200TLX |
Electrical Characteristics
(Notes 2, 7) Limits in standard typeface are for T
A
= T
J
= 25C. Limits in
boldface
type apply over the full operating ambient temperature range (25C
≤
T
= T
≤
+85C). Unless otherwise noted,
specifications apply to the LM3200 with: PV
IN
= V
DD
= EN = 3.6V, BYP = 0V. (Continued)
Symbol
V
IL
Parameter
Conditions
Min
Typ
Max
Units
Logic Low Input
Threshold for EN, BYP
Pin Pull Down Current
for EN, BYP
V
CON
to V
OUT
Gain
V
CON
Input Leakage
Current
0.4
V
I
PIN
EN, BYP = 3.6V
5
10
μA
Gain
I
CON
3
V/V
V
CON
= 1.2V
10
nA
System Characteristics
in the typical application circuit are used.
These parameters are not guaranteed by production testing.
The following spec table entries are guaranteed by design if the component values
Symbol
T
RESPONSE
Time for V
OUT
to Rise
from 0.8V to 3.4V in
PWM Mode
C
CON
V
CON
Input
Capacitance
T
ON_BYP
Bypass FET Turn On
Time In Bypass Mode
Parameter
Conditions
Min
Typ
Max
Units
V
IN
= 4.2V, C
OUT
= 4.7 μF,
R
LOAD
= 15
L = 2.2 uH
V
CON
= 1V,
Test frequency = 100 kHz
V
IN
= 3.6V, V
CON
= 0.267V,
C
OUT
= 4.7 μF, R
LOAD
= 15
BYP = Low to High
(Note 10)
25
μs
15
pF
30
μs
T
BYP
Auto Bypass Detect
Delay Time
10
15
20
μs
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of
the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the
Electrical Characteristics tables.
Note 2:
All voltages are with respect to the potential at the GND pins.
Note 3:
Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at T
J
= 150C (typ.) and disengages at T
J
=
130C (typ.).
Note 4:
The Human body model is a 100 pF capacitor discharged through a 1.5 k
resistor into each pin. (MIL-STD-883 3015.7) The machine model is a 200 pF
capacitor discharged directly into each pin.
Note 5:
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be
de-rated. Maximum ambient temperature (T
A-MAX
) is dependent on the maximum operating junction temperature (T
J-MAX-OP
= 125C), the maximum power
dissipation of the device in the application (P
D-MAX
), and the junction-to ambient thermal resistance of the part/package in the application (
θ
JA
), as given by the
following equation: T
A-MAX
= T
J-MAX-OP
– (
θ
JA
x P
D-MAX
).
Note 6:
Junction-to-ambient thermal resistance (
θ
JA
) is taken from thermal measurements, performed under the conditions and guidelines set forth in the JEDEC
standard JESD51-7. A 1" x 1", 4 layer, 1.5 oz. Cu board was used for the measurements.
Note 7:
Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm.
Note 8:
The LM3200 is designed for mobile phone applications where turn-on after power-up is controlled by the system controller and where requirements for a
small package size overrule increased die size for internal Under Voltage Lock-Out (UVLO) circuitry. Thus, it should be kept in shutdown by holding the EN pin low
until the input voltage exceeds 2.7V.
Note 9:
Over-Voltage protection (OVP) threshold is the voltage above the nominal VOUT where the OVP comparator turns off the PFET switch while in PWM mode.
Note 10:
V
is compared to the programmed output voltage (V
). When V
–V
falls below V
for longer than T
the Bypass FET turns on and the
switching FETs turn off. This is called the Bypass mode. Bypass mode is exited when V
–V
exceeds V
BYPASS+
for longer than T
, and PWM mode returns.
The hysterisis for the bypass detection threshold V
BYPASS+
– V
BYPASS
will always be positive and will be approximately 200 mV(typ.).
Note 11:
Shutdown current includes leakage current of PFET and Bypass FET.
Note 12:
Electrical Characteristic table reflects open loop data (FB=0V and current drawn from SW pin ramped up until cycle by cycle current limit is activated).
Refer to datasheet curves for closed loop data and its variation with regards to supply voltage and temperature. Closed loop current limit is the peak inductor current
measured in the application circuit by increasing output current until output voltage drops by 10%.
Note 13:
Bypass FET current limit is defined as the load current at which the FB voltage is 1V lower than V
IN
.
L
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LM3200TL | Miniature, Adjustable, Step-Down DC-DC Converter with Bypass Mode for RF Power Amplifiers |
| LM3200 | Miniature, Adjustable, Step-Down DC-DC Converter with Bypass Mode for RF Power Amplifiers |
| LM32010P | Medium Size Graphic Type LCD Module |
| LM3201921 | DEVICE SPECIFICATION for Passive Matrix LCD Module |
| LM32019Pl | Passive Matrix Color LCD Module(無源陣列彩色液晶顯示模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3200TLX/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM32010P | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Medium Size Graphic Type LCD Module |
| LM320-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LM320-15 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| LM32019 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Medium Size Graphic Type LCD Module |
發布緊急采購，3分鐘左右您將得到回復。