- 您現在的位置：買賣IC網 > PDF目錄358848 > LM3621M-3.0 (NATIONAL SEMICONDUCTOR CORP) Single Cell Lithium-Ion Battery Charger Controller PDF資料下載
參數資料
| 型號： | LM3621M-3.0 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Single Cell Lithium-Ion Battery Charger Controller |
| 中文描述： | BATTERY CHARGE CONTROLLER, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 10/14頁 |
| 文件大小： | 334K |
| 代理商： | LM3621M-3.0 |
Application Information
Battery Charger Operation Information
Figure 4shows a general battery charger configuration using
LM3621. The LM3621 provides all the necessary control
functions for charging Lithium-Ion batteries precisely and
safely. It features constant voltage and constant current
mode operation. The on chip timer provides all critical timing
functions to properly initialize the charging cycle, avoid over
charging the battery above its maximum capacity level, and
cut off charging to a defective battery. The LM3621 also pro-
vides the high accuracy of output voltage regulation without
requiring a trim pot or precision resistors. A built-in power
down switch prevents the battery from discharging through
the LM3621.
Input Supply Voltage
The voltage supply to LM3621 must never exceed 6.0V or
catastrophic damage may occur to the IC. When power is
first applied to the battery charger, the LM3621 will remain in
a reset state until the voltage on the V
pin exceeds 3.4V
for at least one second. This ensures that the power source
is stable before a charge cycle is initiated. Figure 2 shows
the state diagram for the charge cycle operation. Once the
LM3621 emerges from the reset state after power up, it will
not go into the reset state again until the voltage on the V
pin drops below approximately 2.2V. When the LM3621 is in
the reset state, the PFD (Pass FET Drive) pin is pulled low
so that current is not allowed to flow into the load (e.g., Li+
battery). The LM3621 transitions from the reset state to
standby mode when the conditions for a stable power source
are met.
Digital Control Inputs
The LM3621 has four digital input control pins: Enable,
Boost, V
and ChgInt. To ensure proper operation, never
allow unused digital input pins to be left open circuited. En-
able is used to initiate a charge cycle, Boost is used to in-
crease the maximum regulation current output, V
con-
trols the maximum output voltage, and ChgInt is used to
instantaneously interrupt (and resume) a charge cycle in
progress.
Current Boost Mode
This mode is activated when the “Boost” pin is pulled high.
The charger increases the maximum output current equal to
a V
level of 0.9V. This mode of operation is overridden by
a charge interrupt signal.
Charge Interrupt Control
Charging is interrupted with the digital input “ChgInt” pulled
low. The PFD pin is pulled to ground turning off the series
low pass FET. This is useful to prevent charging a battery if,
for example, the ambient temperature is excessively high.
DS100107-4
FIGURE 4. General Application Circuit
www.national.com
10
相關PDF資料 |
PDF描述 |
|---|---|
| LM3621M | Single Cell Lithium-Ion Battery Charger Controller |
| LM3621 | Single Cell Lithium-Ion Battery Charger Controller |
| LM3622M-4.1 | Lithium-Ion Battery Charger Controller |
| LM3622M-4.2 | Card Edge Connector; Contact Termination:Solder; Leaded Process Compatible:Yes RoHS Compliant: Yes |
| LM3622M-8.2 | Lithium-Ion Battery Charger Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3621MX | 功能描述:IC CTRLR LI-ION BAT CHRG 16-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LM3621MX/NOPB | 制造商:Texas Instruments 功能描述:Charge Controller Li-Ion 20mA 4.1V/4.2V 16-Pin SOIC N T/R |
| LM3622 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Lithium-Ion Battery Charger Controller |
| LM3622AM-4.1 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Lithium-Ion Battery Charger Controller |
| LM3622AM-4.1/NOPB | 功能描述:IC CTRLR LI-ION BAT CHRG 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。