- 您現在的位置：買賣IC網 > PDF目錄358861 > LM4120IM5X-3.0 (NATIONAL SEMICONDUCTOR CORP) ; Contacts:SPST-NO; Contact Carry Current:0.5A; Coil Voltage DC Max:5V; Relay Terminals:SMT J-Lead; Switching Current Max:0.25A; Coil Power VDC:3W; Switching Voltage Max:100V; Contact Resistance Max:150ohm RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | LM4120IM5X-3.0 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | ; Contacts:SPST-NO; Contact Carry Current:0.5A; Coil Voltage DC Max:5V; Relay Terminals:SMT J-Lead; Switching Current Max:0.25A; Coil Power VDC:3W; Switching Voltage Max:100V; Contact Resistance Max:150ohm RoHS Compliant: Yes |
| 中文描述： | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 3 V, PDSO5 |
| 封裝： | SOT-23, 5 PIN |
| 文件頁數： | 8/11頁 |
| 文件大小： | 289K |
| 代理商： | LM4120IM5X-3.0 |
Pin Functions
Output (Pin 5):
Reference Output.
Input (Pin 4):
Positive Supply.
Ground (Pin 2):
Negative Supply or Ground Connection.
Enable (Pin 3):
Pulled to input for normal operation. Forcing
this pin to ground will turn-off the output.
REF (Pin 1):
REF Pin. This pin should be left unconnected.
Application Hints
The standard application circuit for the LM4120 is shown in
Figure 1 It is designed to be stable with ceramic output ca-
pacitors in the range of 0.022μF to 0.047μF. Note that
0.022μF is the minimum required output capacitor. These ca-
pacitors typically have an ESR of about 0.1 to 0.5
. Smaller
ESR can be tolerated, however larger ESR can not. The out-
put capacitor can be increased to improve load transient re-
sponse, up to about 1μF. However, values above 0.047μF
must be tantalum. With tantalum capacitors, in the 1μF
range, a small capacitor between the output and the refer-
ence pin is required. This capacitor will typically be in the
50pF range. Care must be taken when using output capaci-
tors of 1μF or larger. These application must be thoroughly
tested over temperature, line and load.
An input capacitor is typically not required. However, a 0.1μF
ceramic can be used to help prevent line transients from en-
tering the LM4120. Larger input capacitors should be tanta-
lum or aluminium.
The reference pin is sensitive to noise, and capacitive load-
ing. Therefore, the PCB layout should isolate this pin as
much as possible.
The enable pin is an analog input with very little hysteresis.
About 6μA into this pin is required to turn the part on, and it
must be taken close to GND to turn the part off (see spec.
table for thresholds). There is a minimum slew rate on this
pin of about 0.003V/μS to prevent glitches on the output. All
of these conditions can easily be met with ordinary CMOS or
TTL logic. If the shutdown feature is not required, then this
pin can safely be connected directly to the input supply.
Floating this pin is not recommended.
Input Capacitor
Noise on the power-supply input can effect the output noise,
but can be reduced by using an optional bypass capacitor
between the input pin and the ground.
Printed Circuit Board Layout Consideration
The mechanical stress due to PC board mounting can cause
the output voltage to shift from its initial value. References in
SOT packages are generally less prone to assembly stress
than devices in Small Outline (SOIC) package.
To reduce the stress-related output voltage shifts, mount the
reference on the low flex areas of the PC board such as near
to the edge or the corner of the PC board.
DS101047-32
FIGURE 1.
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM4120AIM5X-2.0 | Precision Micropower Low Dropout Voltage Reference |
| LM4120IM5X-2.0 | IC,Normally-Open Panel-Mount Solid-State Relay,1-CHANNEL,M:HL092HW048 |
| LM4120AIM5-4.1 | Precision Micropower Low Dropout Voltage Reference |
| LM4120AIM5-5.0 | Precision Micropower Low Dropout Voltage Reference |
| LM4120IM5-5.0 | Precision Micropower Low Dropout Voltage Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4120IM5X-4.1 | 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
| LM4120IM5X-4.1/NOPB | 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
| LM4120IM5X-5.0 | 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
| LM4120IM5X-5.0/NOPB | 功能描述:基準電壓& 基準電流 RoHS:否 制造商:STMicroelectronics 產品:Voltage References 拓?fù)浣Y(jié)構:Shunt References 參考類型:Programmable 輸出電壓:1.24 V to 18 V 初始準確度:0.25 % 平均溫度系數（典型值）:100 PPM / C 串聯 VREF - 輸入電壓（最大值）: 串聯 VREF - 輸入電壓（最小值）: 分流電流（最大值）:60 mA 最大工作溫度:+ 125 C 封裝 / 箱體:SOT-23-3L 封裝:Reel |
| LM4121 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Precision Micropower Low Dropout Voltage Reference |
發布緊急采購，3分鐘左右您將得到回復。