- 您現在的位置：買賣IC網 > PDF目錄30753 > LM4841MH/NOPB (NATIONAL SEMICONDUCTOR CORP) 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | LM4841MH/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 6/31頁 |
| 文件大?。?/td> | 1138K |
| 代理商： | LM4841MH/NOPB |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Application Information
ELIMINATING OUTPUT COUPLING CAPACITORS
Typical single-supply audio amplifiers that can switch be-
tween
driving
bridge-tied-load
(BTL)
speakers
and
single-ended (SE) headphones use a coupling capacitor on
each SE output. This capacitor blocks the half-supply volt-
age to which the output amplifiers are typically biased and
couples the audio signal to the headphones. The signal
return to circuit ground is through the headphone jack’s
sleeve.
The LM4841 eliminates these coupling capacitors. Amplifi-
erA+ (pin 28 on MT/MH) is internally configured to apply
V
DD/2 to a stereo headphone jack’s sleeve. This voltage
matches the quiescent voltage present on the AmpAout- and
AmpBout- outputs that drive the headphones. The head-
phones
operate
in
a
manner
very
similar
to
a
bridge-tied-load (BTL). The same DC voltage is applied to
both headphone speaker terminals. This results in no net DC
current flow through the speaker. AC current flows through a
headphone speaker as an audio signal’s output amplitude
increases on the speaker’s terminal.
When operating as a headphone amplifier, the headphone
jack sleeve is not connected to circuit ground. Using the
headphone output jack as a line-level output will place the
LM4841’s one-half supply voltage on a plug’s sleeve con-
nection.
Driving
a
portable
notebook
computer
or
audio-visual display equipment is possible. This presents no
difficulty when the external equipment uses capacitively
coupled inputs. For the very small minority of equipment that
is DC-coupled, the LM4841 monitors the current supplied by
the amplifier that drives the headphone jack’s sleeve. If this
current exceeds 500mA
PK, the amplifier is shutdown, pro-
tecting the LM4841 and the external equipment.
OUTPUT TRANSIENT (’POPS AND CLICKS’)
ELIMINATED
The LM4841 contains advanced circuitry that eliminates out-
put transients (’pop and click’). This circuitry prevents all
traces of transients when the supply voltage is first applied,
when the part resumes operation after shutdown, or when
switching between BTL speakers and SE headphones. Two
circuits combine to eliminate pop and click. One circuit
mutes the output when switching between speaker loads.
Another circuit monitors the input signal. It maintains the
muted condition until there is sufficient input signal magni-
tude (>22mV
RMS, typ) to mask any remaining transient that
may occur. (See Turn On Characteristics).
Figure 3 shows the LM4841’s lack of transients in the differ-
ential signal (Trace B) across a BTL 8
load. The LM4841’s
active-high SHUTDOWN pin is driven by the logic signal
shown in Trace A. Trace C is the VOUT- output signal and
trace D is the VOUT+ output signal. The shutdown signal
frequency is 1Hz with a 50% duty cycle. Figure 4 is gener-
ated with the same conditions except that the output drives a
32
single-ended (SE) load. Again, no trace of output tran-
sients on Trace B can be observed.
20028095
FIGURE 3. Differential output signal (Trace B) is devoid of transients. The SHUTDOWN pin is driven by a shutdown
signal (Trace A). The inverting output (Trace C) and the non-inverting output (Trace D) are applied across an 8
BTL
load.
LM4841
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM4841MHX/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| LM4841MT/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| LM4841MTX/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO28 |
| LM4841LQ/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, QCC28 |
| LM4842MHX/NOPB | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4841MT | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Amplifiers with DC Volume Control, Transient Free Outputs, and Cap-less Headphone Drive |
| LM4841MT/NOPB | 功能描述:IC AMP AUDIO PWR 2.2W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4842 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Amplifiers with DC Volume Control Transient Free Outputs, and Cap-less Headphone Drive |
| LM4842LQ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Amplifiers with DC Volume Control Transient Free Outputs, and Cap-less Headphone Drive |
| LM4842LQ/NOPB | 功能描述:IC AMP AUDIO PWR 2.2W STER 28LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。